Question

Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...

Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components.

Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The assumptions and approximations (if any) used must be clearly shown in the design. The datasheet for the 2N3904 indicates that beta ranges from 100 to 300 for a collector current of 10 mA. Refer the datasheet for various parameters required for the design.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components. Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing the following: 1. DC Current Gain: ?DC = 150 (minimum value) 2. AC Voltage Gain: Av = 12 (minimum value) II. Required Components: 1. Transistor Q1 – 2N2222A producing a VCE between 8 V to 12 V 2. Input AC Source: 10 mVAC (14.14 mVpk) @ 1 kHz 3. Coupling and Bypass Capacitors – 30 µF (suitable for low frequencies) 4. Circuit VCC of...
In a two-story voltage amplifier circuit, there is PNP on the first floor and NPN on...
In a two-story voltage amplifier circuit, there is PNP on the first floor and NPN on the second floor. A total of 10 resistors and a total of 5 capacitors were used in the circuit, 5 resistors per floor. Re resistance of PNP transistor is 63.31 Ω and re resistance of NPN transistor is 15.25 Ω. The input impedance of the first floor is 212.36 Ω and the input impedance of the second floor is 9.1 K Ω. There is...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT