Question

A voice signal of bandwidth 4 Khz is transmitted using binary companded PCM with µ=100, and...

A voice signal of bandwidth 4 Khz is transmitted using binary companded PCM with µ=100, and L=256. Calculate the signal-to-noise ratio at the output. Choose one answer.

  • A. 39.49 dB

  • B. 27.80 dB

  • C. 15.75 dB

  • D. 8.24 dB

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Suppose a full-scale voice signal with bandwidth 10 kHz is sampled at the Nyquist rate and...
Suppose a full-scale voice signal with bandwidth 10 kHz is sampled at the Nyquist rate and quantized by using a b-bit uniform quantizer. The bit stream is then transmitted using binary PAM over an AWGN channel that is capable of passing frequencies in the range of [0, 200kHz]. 1. Suppose that the signal is transmitted at the maximum bit rate and the two-sided spectral density of noise at the receiver is 10-6 W/Hz. What is the required signal power to...
Q14: For the binary sequence in Q13, sketch the resulting waveforms from sinusoidal modulation if the...
Q14: For the binary sequence in Q13, sketch the resulting waveforms from sinusoidal modulation if the modulation type: ASK, BPSK, FSK, QAM, QPSK, QFSK. Q15: A modulating signal ?(?) bandlimited to 4 kHz is sampled at a rate of 10.000 samples/sec. The samples are quantized into 256 levels, binary coded (unipolar NRZ) and transmitted over a channel with ?? (?) = 6.25*10-5 watt/Hz. Each received pulse has energy 2O 10-5 Given that ?? = 1 and ? 2(?) ̅̅̅̅̅̅̅. a-Find...
QUESTION 1 A transmit signal operating at 100 watts suffers a 3dB signal reduction. What is...
QUESTION 1 A transmit signal operating at 100 watts suffers a 3dB signal reduction. What is the strength of your signal after suffering the 3dB hit? a. 97 watts b. 103 watts c. 50 watts d. 50 dB QUESTION 2 Select the correct statement(s) regarding the Shannon Capacity Formula (C=B*log2(1+SNR)). a. the Shannon Capacity formula identifies the theoretical maximum capacity achievable in any digital communications system b. the Shannon Capacity formula tells you that data rates will increase as signal...
A digital signal has four levels. How many bits are needed per level? Draw the digital...
A digital signal has four levels. How many bits are needed per level? Draw the digital signal assume the baud rate is 8 baud per second. Increasing the levels of a signal increases the probability of an error occurring, in other words it reduces the reliability of the system. Why and how can this be resolve? What determines how successful a receiver will be in interpreting an incoming signal? Spectrum of a channel between 5 MHz and 4 MHz; SNRdB...
QUESTION 9 Determine the maximum theoretical data rate possible given a frequency bandwidth of 4 kHz...
QUESTION 9 Determine the maximum theoretical data rate possible given a frequency bandwidth of 4 kHz and SNR=99 dB. a. 26 kbps b. 100 kbps c. 72E6 bps d. 240 Mbps 10 points    QUESTION 10 For guided mediums, insertion loss is dependent upon which of the following? a. number of connectors and splices b. wire diameter c.   signal frequency d. all of the above 10 points    QUESTION 11 Signals on UTP guided medium are in a balanced configuration,...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT