Question

I want to design a full wave rectifier with bandwidth 50mHz and gain 1. What is...

I want to design a full wave rectifier with bandwidth 50mHz and gain 1. What is the circuit and component values? What type of amplifier should I use?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with a peak-to-peak riple of 2V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac volatage sources of any amplitudes needed are avaialable. Draw the circuit diagram for your design, Specify the values of all components used. 2. Repeat Problem 1 with 2 diodes and out-of-phase voltage sources to form a full-wave rectifier.
Design a full-wave bridge rectifier circuit to deliver 10 volts DC with less than 0.1 volt...
Design a full-wave bridge rectifier circuit to deliver 10 volts DC with less than 0.1 volt peak-to-peak ripple into a 1 k load. Assume a 60 Hz input sin wave.
1-Draw the schematics of a full-wave rectifier circuit without smoothing capacitor. Sketch the input and output...
1-Draw the schematics of a full-wave rectifier circuit without smoothing capacitor. Sketch the input and output voltage waveforms? 2- Draw the schematics of a full-wave rectifier circuit with smoothing capacitor. Sketch the input and output voltage waveforms?
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency.
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230...
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230 Volt at 50 Hz. 24 Volt battery will be charged with 15A. An inductor, which is series connected to the battery, is used to limit the current ripple. Only The second harmonics of the output voltage is taken into account. The inductor R/L ratio is 50. The current ripple is allowed to be 4 amp peak to peak. Determine the firing angle and R...
1. Design a second-orderactive low-pass filter to amplify the frequencies below 1 kHzwith gain of Av=150.Sketch...
1. Design a second-orderactive low-pass filter to amplify the frequencies below 1 kHzwith gain of Av=150.Sketch the circuit and determine the component values. 2.Design a second-order active high-pass filter to amplify the frequencies above 500 Hzwith gain of Av=100.Sketch the circuit and determine the component values. 3.Design a second-order active band-pass filter to amplify the frequencies between 500?1000 Hz with gain of Av=200.Sketch the circuit and determine the component values
Write a Report on the following – 1) Describe waveform characteristics for sinusoidal waveforms 2) What...
Write a Report on the following – 1) Describe waveform characteristics for sinusoidal waveforms 2) What is a Diode? Explain forward and reverse biased characteristics of a diode with circuit diagrams. 3) What is a rectifier? Explain half wave and full wave rectifier with circuit diagrams.
My question: what is the truth table for full-comparator?? Full question: Design a comparator circuit for...
My question: what is the truth table for full-comparator?? Full question: Design a comparator circuit for binary numbers using only NAND gates. It should take as input two numbers represented in standard binary, X and Y, and produce two outputs, G and L, which indicate that X is Greater than or Less than Y, respectively. If both outputs are zero, it indicates that the values are equal. Design a half-comparator, full-comparator, and a full four-bit comparator. With nothing more than...
I need full solution Design a circuit with the specifications bellow: 1. The circuit contains at...
I need full solution Design a circuit with the specifications bellow: 1. The circuit contains at least two of each components: DC Voltage source, DC Current source, 2. The circuit contains at least 8 Resistors 3. One of the voltage sources is connected between ground and a non-ground node 4. One of the voltage sources is connected between two non-ground nodes 5. Make sure you need to solve at least 3 equations and 3 unknowns. After you designed the circuit:...
Can you design me a circuit with fixed collector-emitter voltage, the gain is not constant and...
Can you design me a circuit with fixed collector-emitter voltage, the gain is not constant and it varies depending on collector current. I want to generate the beta versus collector current graph with using BJT for a fixed collector-emitter voltage (5V). Collector should span the range (1mA--> 1000mA) or can you tell me how to vary the collector current and keep the collector-emitter voltage fixed? What are the key features to be careful about ? ? What type of components...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT