Question

Q1). [36 marks in total] a) Explain why the number of poles (teeth) in the stator...

Q1). [36 marks in total]

a) Explain why the number of poles (teeth) in the stator and rotor must not be equal for a stepper motor. [6 marks]

b) Provide your recommendations for reduction of magnetic loss in an induction motor [6 marks]

c) Explain that a single-phase winding induction motor cannot generate torque to start and run the rotor [6 marks]

d) Explain the rotor of an induction motor cannot run at the same speed to that of stator field [6 marks]

e) Explain the important differences between a DC motor and an Induction motor [6 marks]

f) Write the relationship between Line voltage, phase voltage, line current and phase current between three phase Star and Delta systems. [6 marks]

Homework Answers

Answer #1

​​​​​​

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
An 8 poles,230V,60Hz delta connected three-phase induction motor has a rotor impedance of 0.025+j0.1 phase the...
An 8 poles,230V,60Hz delta connected three-phase induction motor has a rotor impedance of 0.025+j0.1 phase the stator winding impedance is negligible and the Xm=infinity.Determine a- the speed at maximum torque. b-the maximum torque. c-the staring torque as a percentage of the maximum torque. d-what additional resistance must be inserted in the rotor circuit to make the starting torque equal to 75% of the maximum torque?
Question2: Calculate the total machine losses under this condition: A 415V, 50Hz, 2790rpm, 3 phase, star-connected...
Question2: Calculate the total machine losses under this condition: A 415V, 50Hz, 2790rpm, 3 phase, star-connected induction motor has the following equivalent circuit parameters (all referred to the stator winding) : stator leakage reactance X1= 0.3 ohm, stator resistance R1= 0.2 ohms, rotor leakage reactance X2' = 0.3 ohm, rotor resistance R2' = 0.16 ohm, magnetising reactance XM = 12 ohm, core-loss resistance = 150 ohms. Use the simplified equivalent circuit for the following calculations. Under a certain operating condition...
The following test data apply to a 7.5-hp, three-phase, 220-V, 19-A,60-Hz, four-pole induction motor with a...
The following test data apply to a 7.5-hp, three-phase, 220-V, 19-A,60-Hz, four-pole induction motor with a double-squirrel-cage rotor of design class C (high-starting-torque, low-starting current type): Test 1: No-load test at 60 Hz; Applied voltage V = 219 V line-to-line; Average phase current I1,nl = 5.70 A; Power Pnl =380 W; Test 2: Blocked-rotor test at 15 Hz; Applied voltage V = 26.5 V line-to-line; Average phase current ll,bl = 18.57 A; Power Pbl = 675 W; Test 3: Average...
Q1. please answer the following only without any explain anything wanted to compare my answers with...
Q1. please answer the following only without any explain anything wanted to compare my answers with yours 23 Introduction to AC Drives The inductive_______ of a motor increases as the applied frequency increases. Kick Feedback Reactance Voltage drop To minimize electrical noise, _______ cable should be used to connect the drive to the motor. Double Single strand Solid Shielded To prevent injury the user should wait________ minutes after powering down a powerFlex 70 drive before working on it 60 30...