Question

(a) A factory need a drive system for a conveyer system. Voltage source available is three...

(a) A factory need a drive system for a conveyer system. Voltage source available is three phase 415
Volt, 50 Hz. Electric motor that they use is DC motor.
(i) How the design of DC drive system for that system :
(ii) What the parameters should be considered?
(iii) What type of the DC motor that needed?
(iv) What kind of converters that suitable for this system?
(v) How the control system?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
If the available power source is a single-phase, 60 Hz, ac supply and a separately excited...
If the available power source is a single-phase, 60 Hz, ac supply and a separately excited DC motor is to be fed from this source, configure possible drive circuits for: i) One-Quadrant Operation, ii) Two- Quadrant Operation iii) Four- Quadrant Operation Hints: For one-quadrant operation, the motor control circuit is a half-wave controlled rectifier or a semicontrolled converter and the driver for the separately excited is a semi-controlled converter with a freewheeling diode using the ac supply source. For two-quadrant...
The following test data apply to a 7.5-hp, three-phase, 220-V, 19-A,60-Hz, four-pole induction motor with a...
The following test data apply to a 7.5-hp, three-phase, 220-V, 19-A,60-Hz, four-pole induction motor with a double-squirrel-cage rotor of design class C (high-starting-torque, low-starting current type): Test 1: No-load test at 60 Hz; Applied voltage V = 219 V line-to-line; Average phase current I1,nl = 5.70 A; Power Pnl =380 W; Test 2: Blocked-rotor test at 15 Hz; Applied voltage V = 26.5 V line-to-line; Average phase current ll,bl = 18.57 A; Power Pbl = 675 W; Test 3: Average...
A three-phase, 60-Hz, 4-pole, 440-V (line-line, rms) induction-motor drive has a full-load (rated) speed of 1746...
A three-phase, 60-Hz, 4-pole, 440-V (line-line, rms) induction-motor drive has a full-load (rated) speed of 1746 rpm. The rated torque is 40 Nm. Keeping the air gap flux-density peak constant at its rated value. The frequency and voltage of the motor from above are adjusted such that the fan speed is changed to 600 rpm. The motor should be operating at 3% slip and rated Bm. What is the motor efficiency?
Plate values of a three-phase transformer are given below: 1600 kVA, 15 kV / 0,4 kV,...
Plate values of a three-phase transformer are given below: 1600 kVA, 15 kV / 0,4 kV, 50 Hz, i0 = 1.2%; ukN= 6%, idle losses 2450 W, rated power copper losses 14500 W; Dy5 connected.. III) There is 75% load in the power factor with 0.85 inductance and 0.85 capacity. At what times of the day can capacity loading be seen? What solution should be applied to prevent voltage change? IV) Draw the fastening group. How can this transformer be...
Question 1 a) A new manufacturing plant which operates on parameters such as temperature and pressure,...
Question 1 a) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action....
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL...
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL DETAILS OF THE STEPS ON EACH QUESTIONS SO I COULD FOLLOW UP YOUR WHOLE EXPLANATIONS. PLEASE WRITE THE STEPS ON SOLVING THIS EXAMPLE EX) STEP 1, STEP 2, ETC HANDWRITING IS OKAY AS LONG AS IT IS READABLE. IF YOU HAVE USED THE EQUATIONS OR CONCEPTS, PLEASE STATE IT CLEARLY WHICH ONE YOU HAVE YOU USED SO I COULD FULLY UNDERSTAND THE DETAILS OF...
1. Answer EITHER part (a) OR part (b). (a) A gas scrubber on an oilrig discharged...
1. Answer EITHER part (a) OR part (b). (a) A gas scrubber on an oilrig discharged gas periodically such that an accumulation of hydrocarbon gas nearby had occurred. A contractor welder was dispatched to a job immediately adjacent to the area and it being a shift change and personnel unavailable temporarily, the welder decided to commence welding. As a consequence, an incident occurred. Describe briefly: (i) what you imagine was the incident including any hazards existing prior to or during...
1) Which of the following is not a valid way that a CRM system can collect...
1) Which of the following is not a valid way that a CRM system can collect information? A. accounting system B. order fulfillment system C. inventory system D. customer’s personal computer 2)Which of the following is a common marketing CRM metric? A. number of new prospective customers B. average number of service calls per day C. average time to resolution D. cost per interaction by marketing campaign 3)Which question below represents a CRM reporting technology example? A. Why did sales...
Item 1 In the case below, the original source material is given along with a sample...
Item 1 In the case below, the original source material is given along with a sample of student work. Determine the type of plagiarism by clicking the appropriate radio button. Original Source Material Student Version A communication channel is the means by which messages get from one individual to another. The nature of the information-exchange relationship between a pair of individuals determines the conditions under which a source will or will not transmit the innovation to the receiver and the...
Item 1 In the case below, the original source material is given along with a sample...
Item 1 In the case below, the original source material is given along with a sample of student work. Determine the type of plagiarism by clicking the appropriate radio button. Original Source Material Student Version There is a desperate need for theorists and researchers to generate and refine a new breed of learning-focused instructional design theoriesthat help educators and trainers to meet those needs, (i.e., that focus on learning and that foster development of initiative, teamwork, thinking skills, and diversity)....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT