Question

Design a four resister BJT (CE) bias circuit (using any method) for the following       specifications:...

Design a four resister BJT (CE) bias circuit (using any method) for the following

      specifications:

            ICQ= 1.5 mA,   VCEQ=5 V,   Vcc=14 V.   Find all resistor values.

            Assume a BJT transistor (npn) with β=100 and VBE=0.7V

            Draw the designed circuit with all values.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing the following: 1. DC Current Gain: ?DC = 150 (minimum value) 2. AC Voltage Gain: Av = 12 (minimum value) II. Required Components: 1. Transistor Q1 – 2N2222A producing a VCE between 8 V to 12 V 2. Input AC Source: 10 mVAC (14.14 mVpk) @ 1 kHz 3. Coupling and Bypass Capacitors – 30 µF (suitable for low frequencies) 4. Circuit VCC of...
Design a second order (two pole) low-pass filter for the following specifications Cut-off frequency, fo or...
Design a second order (two pole) low-pass filter for the following specifications Cut-off frequency, fo or fH = 8kHz   Maximally Flat, i.e. Q=1/√2 > Justify any assumption you make. > Draw circuit with all designed values. > Draw the frequency response (Gain magnitude only)
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
Assume that you are asked to design a logic circuit with the following specifications, using K-map....
Assume that you are asked to design a logic circuit with the following specifications, using K-map. The circuit has two inputs X and Y and three outputs O0, O1 and O2. This circuit operates as follows: (1) the output (O0) will be high when XY only, and (3) the output (O2) will be high when X=Y only. a)Create the truth table for this logic circuit. b) Show the Karnaugh maps. c) Draw the schematic, using logic gates.
Assume that you are asked to design a logic circuit with the following specifications, using K-map....
Assume that you are asked to design a logic circuit with the following specifications, using K-map. The circuit has two inputs X and Y and three outputs O0, O1 and O2. This circuit operates as follows: (1) the output (O0) will be high when X<Y only, (2) the output (O1) will be high when X>Y only, and (3) the output (O2) will be high when X=Y only. a. (3 points) Create the truth table for this logic circuit. b. (3...
Part 1: I need to design a circuit using only resistors and capacitors that will filter...
Part 1: I need to design a circuit using only resistors and capacitors that will filter out a signal above a specific frequency. In order to be deemed a success, the peak voltage across your capacitor must be equal to 20% of the peak voltage provided by the function generator at the frequency f_theory. Full credit on this lab requires that your percent error in Part 2 is less than 5%. f theory = 1699Hz Available values of resistance are...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with a peak-to-peak riple of 2V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac volatage sources of any amplitudes needed are avaialable. Draw the circuit diagram for your design, Specify the values of all components used. 2. Repeat Problem 1 with 2 diodes and out-of-phase voltage sources to form a full-wave rectifier.
Using the model proposed by Lafley and Charan, analyze how Apigee was able to drive innovation....
Using the model proposed by Lafley and Charan, analyze how Apigee was able to drive innovation. case:    W17400 APIGEE: PEOPLE MANAGEMENT PRACTICES AND THE CHALLENGE OF GROWTH Ranjeet Nambudiri, S. Ramnarayan, and Catherine Xavier wrote this case solely to provide material for class discussion. The authors do not intend to illustrate either effective or ineffective handling of a managerial situation. The authors may have disguised certain names and other identifying information to protect confidentiality. This publication may not be...
      MK Restaurant: Branding of Thai-Style Hotpot The restaurant industry is one of the most...
      MK Restaurant: Branding of Thai-Style Hotpot The restaurant industry is one of the most competitive in Thailand. With a large number of players ranging from restaurants in five-star hotels, global fast-food chains to small stalls along the streets and everything in between, the Thais are spoiled for choice. In addition, as the world becomes globalized, consumers are familiar with international dishes and would not hesitate to try new offerings from the other side of the globe. As a...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT