Question

Design a non-inverting amplifier with a gain of +5. The input resistance should not be smaller...

Design a non-inverting amplifier with a gain of +5. The input resistance should not be smaller than 10 kΩ.

Homework Answers

Answer #1

Here is the design.I mentioned explination below.If you have any doubts ask me in the comment section below.If you like please upvote:)

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design an inverting amplifier with a gain of ‒5. The input resistance should not be smaller...
Design an inverting amplifier with a gain of ‒5. The input resistance should not be smaller than 10 kΩ.
1. For an inverting amplifier with a voltage gain of -10 and an input resistance of...
1. For an inverting amplifier with a voltage gain of -10 and an input resistance of 1 kilohm, calculate the value of the feedback resistor (Rf) in kilohms. 2. For a non-inverting amplifier with a voltage gain of 11, what is the ratio of R2 to R1? 3. Which pin of the 741 op-amp should be connected to the positive supply voltage (e.g. +15V)? 4. For an inverting amplifier with a voltage gain of -20 and an input resistance of...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design a non-inverting amplifier with a gain of ×10. Design the amplifier so that the output current from the op-amp at maximum output voltage +15V is no larger than 15 mA. 3. Design a current summing amplifier that finds the algebraic sum of two input voltages: VOUT = - (V1 + V2) . Design the amplifier so that output current from the op-amp at maximum...
a)What is the formula for the gain of an inverting operational amplifier circuit with input resistor...
a)What is the formula for the gain of an inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit. b)What is the formula for the gain of a non-inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit. c)What is the gain of a voltage follower operational amplifier circuit? What is the input impedance of this circuit? Draw the circuit.
In a differential amplifier, the non-inverting input is 3cos (600t + 45◦) mV and the inverting...
In a differential amplifier, the non-inverting input is 3cos (600t + 45◦) mV and the inverting input is 4cos (600t - 45◦) mV. The output is vo = 3cos (600t + 45◦ ) + 4.004cos (600t - 45◦ ) V. The CMRR is _____dB.
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals...
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals to -10 (Acl=Vout/Vin)
In a differential amplifier, the non-inverting input is 3 cos (600t - 45 ° ) mV...
In a differential amplifier, the non-inverting input is 3 cos (600t - 45 ° ) mV and the inverse input is 4cos (600t - 45◦ ) mV. The output is vo = 3cos (600t - 45◦ ) + 4.004cos (600t - 45◦ ) V. The CMRR is _______ dB.
In a differential amplifier, the noninverting input is 3cos(600t + 45°) mV and the inverting input...
In a differential amplifier, the noninverting input is 3cos(600t + 45°) mV and the inverting input is 4cos (600t - 45°) mV. The output is vo = 3cos (600t + 45°) + 4.004cos (600t - 45°) V. The CMRR is of? The unit must be in dB.
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
Power supply voltage for the photodiode Resistor value (Vsensor) = 120 V Output voltages over black...
Power supply voltage for the photodiode Resistor value (Vsensor) = 120 V Output voltages over black (Vsensor) Output voltage over white (Vsensor) 1 V 3 KΩ 33 mV 120 mV b. Amplifier subcircuit. Vsensor has to be amplified to obtain the specified sensor output of 3.3 V when the photodiode is over the white background. Calculate the gain required to achieve this. Explain whether this requires an inverting or non-inverting amplifier. Calculate the resistor values to achieve this gain. Explain...