Question

Using bjt 2n2222 design an amplifier with vdd=20V and an output impedance less than 50. Capable...

Using bjt 2n2222 design an amplifier with vdd=20V and an output impedance less than 50. Capable of driving 50ohms load. And a gain of 10 Volts.
Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design a non-inverting amplifier with a gain of ×10. Design the amplifier so that the output current from the op-amp at maximum output voltage +15V is no larger than 15 mA. 3. Design a current summing amplifier that finds the algebraic sum of two input voltages: VOUT = - (V1 + V2) . Design the amplifier so that output current from the op-amp at maximum...
Design an inverting amplifier to meet the following requirements. You will need an op amp circuit...
Design an inverting amplifier to meet the following requirements. You will need an op amp circuit plus a BJT push pull output circuit to get the power required. ein = +4 dBu at audio frequencies 40 W to a 5 Ω load input impedance 4.9 k Ω TA = 40° C and Tj max = 140° C power supplies: ±18Vdc and ±28Vdc, each at 6 Adc Show all work. Please help thank you!
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals...
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals to -10 (Acl=Vout/Vin)
Consider an NPN BJT with the following parameters. Beta = 85, Cmu = 1 pF, Co...
Consider an NPN BJT with the following parameters. Beta = 85, Cmu = 1 pF, Co = .5 pF, and Cpi = 6 pF. With IC = 70 mA, r0 = 50 Ohms. RLOAD = 50 Ohms and RSIG = 1K. The available power supply is +12V DC. All coupling caps are 1 uF. Design an amplifier circuit using this transistor with a gain of -50. Calculate the upper and lower 3 dB points of your design. There is a...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input voltage internal resistance RS that having a gain of +0.2. The specification of the circuit is given as below: Supply voltage, VCC = +12 V; Input impedance, Zi = 10 k; cut-off frequency from source capacitor, fLS = 40 Hz; cut-off frequency from gate capacitor, fLG = 4 Hz; VGSQ = -2.86 V; IDSS = 16 mA and Vp = -4 V
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components. Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components. Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The...
1. If a system has a gain greater than 1: ____________________ 2. If a system has...
1. If a system has a gain greater than 1: ____________________ 2. If a system has a gain equal to 1: ____________________ 3. If a system has a gain less than 1: ____________________ 4. If a system has a gain greater than 0 dB: __________________ 5. If a system has a gain equal to 0 dB: ____________________ 6. If a system has a gain less than 0 dB: __________________ 7. For a voltage amplifier to increase the source voltage: Rin...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT