Question

An FM signal,2000 sin(2n x 10"t+ 2sin Tux 10't),is applied to a 50 ohms antenna.Determine: (a)The...

An FM signal,2000 sin(2n x 10"t+
2sin Tux 10't),is applied to a 50 ohms
antenna.Determine:
(a)The carrier frequency.
(b)The transmitter power.
(c)The modulating index.
(d)The intelligence signal frequency.
(e)The bandwidth(using the two
methods)

Homework Answers

Answer #1

answered well..

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A carrier signal, Vc(t) = 5cos(1π3000t) F is frequency modulated by a modulating signal of 4...
A carrier signal, Vc(t) = 5cos(1π3000t) F is frequency modulated by a modulating signal of 4 kHz with a modulation index of 2. The FM wave is transmitted through a 50 Ω antenna. With the aid of Bessel Function Table, determine the: number of sets of significant sidebands, frequency deviation, carrier swing, minimum and maximum frequency of the FM signal, bandwidth using Bessel Function Table, frequencies of all the significant sidebands, total power of the FM signal. Hence, sketch and...
An audio frequency signal 10 sin(2π×500t) is used to amplitude modulate a carrier of 50 sin(2π×105...
An audio frequency signal 10 sin(2π×500t) is used to amplitude modulate a carrier of 50 sin(2π×105 t). Calculate: a) Frequency of side bands b) Bandwidth c) Modulation index d) Amplitude of each side band. e) Total power delivered to a load of 600Ω.
1. An amplitude modulated system has following parameters: Modulating signal frequency fm = 500 Hz, Carrier...
1. An amplitude modulated system has following parameters: Modulating signal frequency fm = 500 Hz, Carrier frequency fc = 2KHz. Draw a two-sided spectrum with approximately scaled frequencies and amplitude. Consider perfect modulation (mod index = 1). 2. What is the typical range of AM modulation index (depth)? What will happen if it is at the lowest value or highest value in the range? What will happen if it goes beyond the range? too low a level of modulation and...
Question : Design the low and high pass filter for the signal, x(t) = 10 sin...
Question : Design the low and high pass filter for the signal, x(t) = 10 sin (10 t) + 1 sin (1000 t) by MATLAB Is below answer right? at ?High pass , 5row shouldn't this change from sin(100*t) ? sin(1000*t) x = 10*sin(10*t) + 1*sin(100*t); ?   x = 10*sin(10*t) + 1*sin(1000*t); ??? ..................................................................................................................................................... ?Low pass clc; rng default Fs=2000; t=linspace(0,1,Fs); x=10*sin(10*t)+sin(1000*t)%given signal n=0.5*randn(size(t));%noise x1=x+n; fc=150; Wn=(2/Fs)*fc; b=fir1(20,Wn,'low',kaiser(21,3)); %fvtool(b,1,’Fs’,Fs) y=filter(b,1,x1); plot(t,x1,t,y) xlim([0 0.1]) xlabel('Time (s) ') ylabel('Amplitude') legend('Original Signal','Filtered Data')...
Assignments Generate and plot the signal x1(t) = 1+ sin (4pt), for t ranging from -1...
Assignments Generate and plot the signal x1(t) = 1+ sin (4pt), for t ranging from -1 to 1 in 0.001 increments. Use proper axes labels with title. Generate and plot the function x2(t) = sin (30pt), for t ranging from -1 to 1 in 0.001 increments. Use proper axes labels with title. Generate and plot the combination function x3(t) = x1(t)*x2(t) as above. Use proper axes labels with title. Generate and plot the sum of two cosine waves   v1(t) =...