Question

A copper column has 0.5 meter radius. It carries a load of 30 MN. If the...

A copper column has 0.5 meter radius. It carries a load of 30 MN. If the deformation is entirely elastic, calculate the compressive stress and strain

Homework Answers

Answer #1

Since there are some equations, I preferred a handwritten note. Results are tabulated in the answer for your easier understanding. Hope that it is clear for you and it really helped you.

If you are clear, please help me by rating it with a thumbs up.

In case of any doubt, please feel free to ask in the comment section. Thank you.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
(30 pts) A short reinforced concrete column is subjected to a 1000 kN axial compressive load....
(30 pts) A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli of elasticity of plain concrete and steel are 25 GPa and 207 GPa, respectively, and the cross-sectional area of steel is 2% of that of the reinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following: a. the modulus of elasticity of the reinforced concrete b....
1. A steel sheet metal of 0.0265-in thick is bent to a radius of 0.5-in. Assuming...
1. A steel sheet metal of 0.0265-in thick is bent to a radius of 0.5-in. Assuming that its yield stress is 300 MPa, calculate (a) the radius of the part after spring back and (b) the required bend angle to achieve a 90o bend after spring back has occurred. 2. Prove that Engineering strain of a sheet metal is                          e = 1 / [ ( 2 R / t ) + 1 ]
A copper coil with 30 turns and radius 10 cm has a magnetic field going through...
A copper coil with 30 turns and radius 10 cm has a magnetic field going through it which changes in time according to the formula B = 5e-0.3t Tesla. The radius of the wire is 0.24 mm and the resistivity of copper is 1.68 x 10-8 Ωm. (a) Calculate the induced voltage in the coil at 4 seconds. (b) Calculate the induced current in the coil at 4 seconds.
A copper coil with 30 turns and radius 10 cm has a magnetic field going through...
A copper coil with 30 turns and radius 10 cm has a magnetic field going through it which changes in time according to the formula B = 5e-0.3t Tesla. The radius of the wire is 0.24 mm and the resistivity of copper is 1.68 x 10-8 Ωm. (a) Calculate the induced voltage in the coil at 4 seconds. (b) Calculate the induced current in the coil at 4 seconds.
A shaft of 2m length, 30 mm radius, with a wall thickness of 5 mm has...
A shaft of 2m length, 30 mm radius, with a wall thickness of 5 mm has a torque applied of 450 N. If the material has a G value of 275 GPa, what is the angular deflection in radians and degrees? Hint, you need to calculate the J value, T x l/J x G = deflection, and then convert to degrees. (up to 15 points) A torque of 1500 N on a shaft of 20 mm radius will have what...