Question

A horizontal curve is being designed for a new four-lane roadway with 11-ft lanes. The PT...

A horizontal curve is being designed for a new four-lane roadway with 11-ft lanes. The PT is located at station 1050+20, the design speed is 45 mph and maximum superelevation of 4%. If the central angle of the curve is 30 degrees, what is the radius of the curve and location of the PC and PI?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station...
A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station 10+00 and PT at station 13+70. The central angle is 25 degrees, the superelevation is 4%, and 40 ft of clearance is available between an obstruction and the centerline. Determine the maximum safe design speed to the nearest 5 mph.
A single-lane racetrack is being constructed with a 150 mph design speed. A curve on this...
A single-lane racetrack is being constructed with a 150 mph design speed. A curve on this track has a radius of 4500 ft, central angle of 30 degrees, and a PI located at station 150+40. If the coefficient of side friction is 0.3, what superelevation is required for safe vehicle travel at the design speed? Also, determine the length of the curve and station of the PC and PT.
A horizontal curve of radius 5620 ft is designed for 60 mph. The roadway is a...
A horizontal curve of radius 5620 ft is designed for 60 mph. The roadway is a 4-lane undivided highway with 12-ft lanes. A tree is located on the inside of the curve only 42 ft from the center of the road. Does it pose a stopping sight distance problem for the drivers travelling at the design speed? Show all supporting calculations.
A section of a roadway has a horizontal curve with superelevation of 6% and central angle...
A section of a roadway has a horizontal curve with superelevation of 6% and central angle of 40o. The design speed of the section is 60 mph. There are two lanes on the curve, each 12 ft wide. Determine: (a) The degree of the curve. (b) The length of the curve. (c) The minimum distance of an obstruction from the centerline of the innermost lane.
A horizontal curve with a 300 intersecting angle on a two-lane highway with 12-ft has a...
A horizontal curve with a 300 intersecting angle on a two-lane highway with 12-ft has a 60 mph design speed. The radius for the horizontal curve has been set to 1,250 ft. The PI is located at station 85 + 29.14 and the normal crown on the tangent is 2%. Determine: a) Tangent to Spiral (TS) station, b) Spiral to Curve (SC) station, c) Curve to Spiral (CS) station, and d) Spiral to Tangent (ST) station.
A horizontal curve with a 300 intersecting angle on a two-lane highway with 12-ft has a...
A horizontal curve with a 300 intersecting angle on a two-lane highway with 12-ft has a 60 mph design speed. The radius for the horizontal curve has been set to 1,250 ft. The PI is located at station 85 + 29.14 and the normal crown on the tangent is 2%. Determine: a) Tangent to Spiral (TS) station, b) Spiral to Curve (SC) station, c) Curve to Spiral (CS) station, and d) Spiral to Tangent (ST) station.
ou are asked to design a horizontal curve for a two-lane road. The road has 12-ft...
ou are asked to design a horizontal curve for a two-lane road. The road has 12-ft lanes. Due to expensive excavation, it is determined that a maximum of 35 ft can be cleared from the road’s centerline toward the inside lane to provide for stopping sight distance. Also, local guidelines dictate a maximum superelevation of 0.08 ft/ft. Determine the design speed for this curve (mph)?
a highway curve for a rural two-lane road connects front and back tangents at Station 74+30...
a highway curve for a rural two-lane road connects front and back tangents at Station 74+30 at an angle (delta) of 38 degrees 16’ 31”. using the maximum allowable superelevation for the curve,(a) what would be its minimum radius for design for a posted speed of 55mph? (b) What would be the station locations of the PC and PT for this curve? (c) If the inner radius was kept clear of all visual obstructions out to a distance of 45...
a horizontal curve has a tangent length of 500 ft is to be designed with deflection...
a horizontal curve has a tangent length of 500 ft is to be designed with deflection angle 90 the point of the beginning of the curve pc station is 100 determine the radius of the curve R determine the length of the curve L determine the station of the end of the curve point PT
A developer is having a single-lane raceway constructed with a 180 km/h design speed. A curve...
A developer is having a single-lane raceway constructed with a 180 km/h design speed. A curve on the raceway has a radius of 320 m, a central angle (D) of 30 degrees, and PI stationing at 11+511.200. If the design coefficient of side friction is 0.20, determine the superelevation required at the design speed? Make sure you use the exact equation for R and not the approximate equation for R. Include a discussion (a short paragraph) of why this important....