Question

2. A simply supported beam has a width of 200mm and
depth of 400mm is 4m long. It carries a

uniformly distributed load of 20 kN/m over the whole beam and a
point load of 40 kN at the

center of the beam. Compute the maximum deflection if the maximum
slope produced in the

beam is 2× ??-3 radian.

Answer #1

. A simply supported beam has a width of 200mm and
depth of 400mm is 4m long. It carries a
uniformly distributed load of 20 kN/m over the whole beam and a
point load of 40 kN at the
center of the beam. Compute the maximum deflection if the maximum
slope produced in the
beam is 2× ??-3 radian.

2. A simply supported beam has a width of 200mm and
depth of 400mm is 4m long. It carries a
uniformly distributed load of 20 kN/m over the whole beam and a
point load of 40 kN at the
center of the beam. Compute the maximum deflection if the maximum
slope produced in the
beam is 2× ??-3 radian. (6 M
Blease i want prompt clear solution for this question in
detail,.

A simply supported beam is 3 m long. It carries a uniformly
distributed load of 6 kN/m throughout its span and a concentrated
load of 15 kN at a point 2 m from the left support. Assuming that
the beam has a rectangular shape whose width and depth are 150 mm
and 250 mm, respectively. Determine the maximum flexural stress in
MPa developed in the beam.

A 356 x 171 US45 steel beam is simply supported at the ends of a
span of 5.5 m. The beam carries a safe inclusive UDL of 12kN/m and
a point load of 75 kN at mid-span. Calculate the maximum deflection
due to this load.
Let:
E = 205 000 N/mm2
I = 12070 cm4
deflection δPL = PL/48EI
deflection δudL = 5wL3/384EI

A simply supported laminated composite beam of length 0.075 m
and width 5 mm made of glass/epoxy has the following layup of
[30/-30]4. Assume that each ply is 0.125 mm and material
properties are E1 = 38.6 GPa, E2 = 8.27 GPa,
G12 = 4.14 GPa, ν12 = 0.26. A uniform load of
q=0.6 KN/m is applied on the beam. What is the maximum deflection
of the beam?

A rectangular RC beam is simply supported over a span of 8m and
carries a dead load of 15kN/m (including self-weight) and an
imposed load of 8kN/m. The beam is 250mm wide and has an effective
depth of 400mm. Grade 30 concrete is to be used.
Determine if the beam should be singly reinforced or
doubly reinforced.

simply supported timber beam is 14 feet long with
cross-sectional dimensions of 4 in. wide by 10 in. tall. The beam
is supported at its ends and carries a concentrated load of 5 kips
at its center. The modulus of elasticity is 1.7×106
psi.
The deflection at the center is most nearly

A simply supported reinforced concrete beam has a width (b) of
14 inches, and an effective depth (d) of 24 inches. It is
reinforced with 3 # 8 bars. Assume 60-ksi steel and 3000-psi
concrete. Determine the resisting moment (Mr) in ft-k that this
beam can safely sustain.
Problem 2
The beam given in Problem 1 has a span of 21 ft. It is supposed
to carry a uniformly distributed service dead load of 3.7 k/ft, in
addition to its...

Calculate the bending capacity of a simply supported concrete
beam.
Beam is 6m long and supporting dead load of 20KN/m and live load
of 10KN/m. Compressive strength of the concrete is 25MPa and yield
strength of rebars is 500MPa.
Concrete beam is 300mm height 200mm width.

Plot the shear force and bending moment digrams for an
8m long beam simply supported at 0m and 6m. There is a distributed
load of 10 KN/m between the two supports and there is a point load
of 20kN located at the end of the beam.

ADVERTISEMENT

Get Answers For Free

Most questions answered within 1 hours.

ADVERTISEMENT

asked 7 minutes ago

asked 14 minutes ago

asked 28 minutes ago

asked 59 minutes ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 2 hours ago