Question

how to design a pile foundation knowing the soil profile knowing the soil profile and the...

how to design a pile foundation knowing the soil profile knowing the soil profile and the load applied, how do i proceed what are the steps?

Homework Answers

Answer #1
  1. Selection of Pile-Soil Model.(if guven not required as in question given)
  2. Selection of Pile Structure Model:-The selection of the pile- structure model for analysis and design of a pile-founded structure must con- sider the following three critical items:. Type of structure (concrete or steel). Type of analysis (rigid or flexible base). Pile-head fixity (fixed, pinned, or partially fixed)
  3. Selection of Load Cases.( if given not required as in question given)
  4. Selection of Design Criteria.
  5. Deformations. The pile stiffnesses in the lateral and axial directions is determined by a nonlinear analysis assuming a limiting deformation.
  6. Initial Layout.
  7. Final Layout.
  8. Design of Pile Cap.

if helps give ?.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A plate load test was carried out on a sand soil at the expected foundation depth...
A plate load test was carried out on a sand soil at the expected foundation depth on a circular plate of 45 cm diameter. Failure of the soil below plate occurred when the applied load on plate reached 734 kg. If a square footing of 3 m width is going to be constructed on the same soil and at the same testing depth, what will be the allowable bearing capacity in kg/cm2. (Take F.S = 3).
A 0.5 m in diameter concrete pile is to be driven in clayey soil with following...
A 0.5 m in diameter concrete pile is to be driven in clayey soil with following properties :qu= 150 kn/m^2 and unit weight =180.10 kn/m^3 the design capacity of pile is 1000 kn .what should be the length of pile for fs=2
A 300 kN point load is applied to a soil profile that consists of 7 meters...
A 300 kN point load is applied to a soil profile that consists of 7 meters of sand (γt = 19 kN/m3 ) above 4 meters of clay (γt = 17.5kN/m3 ) with the groundwater table at a depth of 5 meters. The clay has an OCR = 1.6, an initial void ratio of 0.86, a Cc=0.64 and a Cr=0.12. The sand has a Cc = 0.35 and an initial void ratio of 0.68. Calculate the overall settlement of the...
Consider a 1.2 m depth soil profile with 3 layers. The dry bulk density of each...
Consider a 1.2 m depth soil profile with 3 layers. The dry bulk density of each layer (top, center, bottom) is 1.20, 1.35, and 1.48 g/cm3 . The top 30-cm layer has a water content of 0.12 g/g, the center 50-cm layer has a water content of 0.18 g/g, and the bottom 40 cm layer has a water content of 0.22 g/g.What is the total amount of water in the whole profile in mm and in inches? How much water...
The foundation of experimental design comes from agriculture. Here is a typical experiment. You want to...
The foundation of experimental design comes from agriculture. Here is a typical experiment. You want to study the effect of two fertilizers, sulfate of ammonia and superphosphate, on the yield of Brussels sprouts. Each fertilizer is used at four levels: 0, 30, 60, and 90 pounds per acre. a/ Describe the response variable b/ Describe the treatments. How many levels for each treatment? c/ List a complete set of treatment combinations. Arrange your list in table form d/ Suppose you...
What is natural angle of repose and how knowing that influences Architects decision of deciding the...
What is natural angle of repose and how knowing that influences Architects decision of deciding the type of foundation? Explain through various types of angles and its property.  
i have to design an all bolted double angle and i have only pu. how can...
i have to design an all bolted double angle and i have only pu. how can i get the length L is it by assumption? and also i need to consider eccentricity and check the connection how do i do that i dont have eccentricity value so what are the steps for calculation?
You are tasked with designing shallow foundation for a commercial structure that will be constructed on...
You are tasked with designing shallow foundation for a commercial structure that will be constructed on CLAY deposits from an ancient lake bed. What important geotechnical information do you need in order to recommend an allowable bearing pressure for the design and ideally, how would you obtain in? Think about what calculations, and input values you would need to make recommendations. Hint: I recommend you simply use bullet points under two columns with the headings “what” and “how”.
You are tasked with designing shallow foundation for a commercial structure that will be constructed on...
You are tasked with designing shallow foundation for a commercial structure that will be constructed on ALLUVIAL SAND deposits from an ancient lake bed. What important geotechnical information do you need in order to recommend an allowable bearing pressure for the design and ideally, how would you obtain in? Think about what calculations, and input values you would need to make recommendations. Hint: I recommend you simply use bullet points under two columns with the headings “what” and “how”.
How to design HVAC system for stadium? how to install one for an existing stadium like...
How to design HVAC system for stadium? how to install one for an existing stadium like Emirate? what is the steps and the things that should I care about it?