Question

Strength of Material A steel rod is 2m long with a diameter of 30mm has a...

Strength of Material

A steel rod is 2m long with a diameter of 30mm has a standard temperature of 18℃. It is exposed in a room with a
temperature of 40 ℃. Use ? = 11.6 ? 10−6/℃ and E = 200 GPa. Find a.) the thermal deformation, b.) thermal stress and
c.) instead of heating the rod, what equivalent axial deformation is necessary to have a deformation that is the same as
the deformation due to the change in temperature.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
A steel rod without constrain has a length of 200 mm and diameter of 20 mm...
A steel rod without constrain has a length of 200 mm and diameter of 20 mm at a temperature of 25oC. If the rod is heated uniformly to 125oC, what will be the length and diameter (accurate to 1/100 mm). What will be the stress at 125oC? The linear coefficient of thermal expansion of steel is 12.5x10-6 m/m/C.
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 150 N and thermal loading which imposes a longitudinal force of 230 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.5 mm in length at both ends and decreasing by 0.0125 mm at...
5. A solid steel shaft has a diameter of 200mm. The shaft transmits 550kW at 300r/min....
5. A solid steel shaft has a diameter of 200mm. The shaft transmits 550kW at 300r/min. It is also subjected to a bending moment of 10kNm and an end thrust of 400kN. Find: 5.1 The applied torque 5.2 The applied shear stress 5.3 The applied bending stress 5.4 The stress due to the end thrust Draw a stress element and matching Mohr’s circle clearly showing Both principle stresses and the maximum shear stress at: 5.5 the top of the shaft’s...
Experimental data: Length L0 of the cold rod (measured with a meter stick): 600 +/- 1...
Experimental data: Length L0 of the cold rod (measured with a meter stick): 600 +/- 1 mm Cross-sectional diameter d of the rod (measured with a caliper): 6.1 +/- 0.1 mm The change in length ∆L after the rod reached its final temperature: 1.04 +/- 0.01 mm The initial temperature of the rod (the room temperature): 22 +/- 1 ̊C The final temperature of the rod shown by the thermometer: 93 +/- 1 ̊C Linear thermal expansion coefficient calculation: 1)...
Consider a low carbon steel allow that has a modulus of resilience of 1.2MPa, an elastic...
Consider a low carbon steel allow that has a modulus of resilience of 1.2MPa, an elastic modulus of 200 GPa, and a tensile strength of 800MPa. A series of experiments were done using this alloy and you are asked to analyze some of the obtained data in the following sections: a). A specimen of this alloy with a rectangular cross section of (15mm x 15mm) and length of 400mm is used in a tensile test. Under an applied tensile stress,...
12)A kettle containing 6 kg of water has just reached its boiling point. How much energy,...
12)A kettle containing 6 kg of water has just reached its boiling point. How much energy, in joules, is required to boil the kettle dry? _____J 13)How much heat would it take to melt a 4 kg block of ice? _____kJ 14)How much heat is required to convert 200 g of ice at -9°C to water at 9°C? _____ cal 15)What is the change in length of a metal rod with an original length of 3 m, a coefficient of...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT