Question

Water discharges from a pond through a rectangular opening that is 1.2m wide and 0.5 m...

Water discharges from a pond through a rectangular opening that is 1.2m wide and 0.5 m high. Use Cd=0.62.

a) Find the discharge through the opening if the water surface in the pond is 0.3m above the opening invert (bottom of the pipe).

b) Find the discharge through the opening if the water surface in the pond is 1m above the opening invert.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A fountain in a pond draws water from the base of the pond, passes it through...
A fountain in a pond draws water from the base of the pond, passes it through a pump with ?? = 25 ?, and along a pipe of length L=3 m, diameter D=15 cm and friction factor f=0.03. The pipe has three 90deg bends (?? = 0.8) before passing through a contraction nozzle (?? = 0.5 based on the upstream velocity) such that the diameter of the outlet nozzle is d=5 cm. The flow then leaves the nozzle moving in...
Water approaches a sharp-crested rectangular weir through a channel that is 2 m wide. The depth...
Water approaches a sharp-crested rectangular weir through a channel that is 2 m wide. The depth of flow in the channel is 1 m. The weir crest is 0.6 m above the base of the channel and has a crest width of 0.8 m. It is located in the centre of the channel. Assuming a coefficient of discharge of 0.61, and ignoring side contractions, determine the discharge over the weir: a) Assuming the approach velocity is zero b) Including the...
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm...
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 65 m below the reservoir surface. The turbine delivers 0.80 MW. Calculate the required flow rate of water in m3 /min if friction is neglected.
During a flood flow, the depth of flow in a 10 m wide rectangular channel at...
During a flood flow, the depth of flow in a 10 m wide rectangular channel at 2 sections 200 m apart was found to be 3.0 m and 2.9 m. respectively. The drop in the water surface elevation was found to be 0.12 m. Estimate the flood discharge through the channel. Assume n = 0.025.
A pond with a total depth (ice + water) of 2.75 m is covered by a...
A pond with a total depth (ice + water) of 2.75 m is covered by a transparent layer of ice, with a thickness of 0.32 m Find the time required for light to travel vertically from the surface of the ice to the bottom of the pond. Express your answer using two significant figures.
EXAMPLE 6.1 A trapezoidal irrigation canal has a bottom width of b¼1.2m, side slopes of m¼2...
EXAMPLE 6.1 A trapezoidal irrigation canal has a bottom width of b¼1.2m, side slopes of m¼2 (2H:1V), and a longitudinal bottom slope of S0¼0.0005. A rectangular sharp-crested weir placed in this channel has a crest height of p¼0.70m, and a crest length of Lw¼0.80m. The water surface elevation at the approach section is h0¼0.77m above the weir crest. Determine the discharge in the canal.
an water vertical sluis gate freely 56 m3/s into a rectangular channel 7 m wide ....
an water vertical sluis gate freely 56 m3/s into a rectangular channel 7 m wide . the gate whic is the same width as the channel is set at a height of 1.4m above the bed and the depth at the vena contracta is .85 m the energy loss in the converging flow at a sluis is quite small so take the head loss B as .05v2 / 2g the normal depth in the downstream hz=2.6m 1. calculate the depth...
Water flows through a pipe that gradually descends from a height of 6.78 m to the...
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.4 m2, and the pipe gradually widens so that its area near the ground is 0.8 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?
Water travels through a pipe at 4 m/s. The pipe changes from a radius of 1...
Water travels through a pipe at 4 m/s. The pipe changes from a radius of 1 m to a radius of 0.5 m.   What is the area of the 1 m radius pipe?   m2 Tries 0/2 What is the area of the 0.5 m pipe? m2 Tries 0/2 What is the velocity of the water after the pipe has changed radii? m/s Tries 0/2 How does the pressure change from the 1 m pipe to the 0.5 m pipe? Enter...
Water flows through a pipe that gradually descends from a height of 6.78 m to the...
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.4 m2, and the pipe gradually widens so that its area near the ground is 0.8 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe? In Pa