Question

A
sturdy column with a hollow rectangle shape is made of steel. 150mm
length and 70mm width, thickness of steel=6mm.

E=200Gpa

-what is the max slenderness ratio if the column is pinned at
both ends 3m long?

-what is the critical load if the column is pinned at both
ends and is 3m?

-what is critical load if the column is fixed at both ends and
is 7m?

Answer #1

a). Maximum slenderness ratio if the column is pinned at both ends 3m long = 104.84.

b). Critical load if column is pinned at both ends 3 m long = 4.482 × 10^17 N.

c). Critical load if the column is fixed at both ends, 7m long = 3.293 × 10^17 N.

(Please give a thumbs up ).

Determine if the following column is long or short, and then
determine the critical load on a steel column having a rectangular
cross section, 12mm by 18mm and a length of 250 mm. It is fixed on
both ends and made from a steel that has the following properties:
E= 209 Gpa and sy = 290 Mpa.
Slenderness ratio = ___________ Cc = _______ Long or short
column = ___________ Critical load = ____________________
Newtons

A hollow, round column has length of 1.5m, material aluminum, OD
= 20mm, and ID = 14mm. Use Sy = 150 MPa for aluminum.
Determine if it is a Johnson or Euler column and find the critical
load for the following end conditions:
A) Pinned-pinned
B) Fixed-pinned
C) Fixed-fixed
D) Fixed-free

Select a light W shape for a column subjected to an axial
compressive load of 1623kN. The unbraced length of column is 5m and
the ends are pinned. Use A36 grade steel.

A steel column has a length of 40 ft and is fixed at both ends.
If the cross sectional area has the dimensions of a wide flange
W10x39, determine the critical load at: 1) fixed to fixed 2) fixed
to pin 3) pin to pin Please put answers in lb. Show all work
please

A
6-m long column is made of a steel girder W200x52 (see the section
properties in the last page). It is loaded concentrically through
the centroid of the section. Given that the steel has the elastic
modulus Est = 210 GPa and the yield stress Y = 340 MPa. Determine
the critical load (Euler Buckling Load, Pcr) where the support at
the column ends are fixed-free support

A hollow circular steel column 2m long and outer diameter 200
mm carries an axial load of 325 kN. If the compressive stress is
150 MPa, lateral strain for external diameter is is 0.000325 and
Poisson’s ratio is 0.3, find the minimum wall thickness required
for the column. Also calculate the shear modulus for the material
of the column. Take E = 210 GPa.

2) A bimetallic strip is made of copper and steel fused
together. The length of each piece is 23 cm at 25 Celsius and the
thickness of the copper is .6mm and the steel is .8mm.
a) If the temperature of the strip
goes from 25 to 35 Celsius, what is the subtended angle of the arc
that the strip makes? [Assume that the thickness does not change
appreciably compared to the length of the pieces]
b) To what temperature...

During construction, field tests were conducted to
assess the suitability of the column to withstand a safe buckling
load of 2.5 kN assuming a factor of safety 4 using two different
hollow columns made up of steel and concrete. Both columns have
same cross section but varying length and different support
conditions. Steel column of length 3 m having external diameter 40
mm was tested with one end fixed and the other end hinged, when
subjected to a compressive stress...

1: During construction, field tests were conducted to assess
the suitability of the column to withstand a safe buckling load of
2.5 kN assuming a factor of safety 4 using two different hollow
columns made up of steel and concrete. Both columns have same cross
section but varying length and different support conditions. Steel
column of length 3 m having external diameter 40 mm was tested with
one end fixed and the other end hinged, when subjected to a
compressive...

A column is made of concrete and reinforced with a W-section
steel with an area of 2000 mm2. The dimension of the column is
300mm x 350mm. The column is subjected to an axial load of 100 kN.
What will be the deformed length of the column? Use Es =
200 GPa and Ec = 25 GPa.

ADVERTISEMENT

Get Answers For Free

Most questions answered within 1 hours.

ADVERTISEMENT

asked 6 minutes ago

asked 6 minutes ago

asked 42 minutes ago

asked 56 minutes ago

asked 56 minutes ago

asked 1 hour ago

asked 2 hours ago

asked 2 hours ago

asked 2 hours ago

asked 2 hours ago

asked 3 hours ago

asked 3 hours ago