Question

The design of a leachate system should minimize leachate on the bottom liner. The maximum thickness...

The design of a leachate system should minimize leachate on the bottom liner. The maximum thickness of leachate allowed on the liner system per RCRA Subittle D is .......(unit of feet)?

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Answer: As per RCRA Subittle D, the maximum thickness of leachate allowed on the liner system is less than one feet.

The full form of RCRA is Resource Conservation and Recovery Act. The RCRA gives EPA (Environmental Protection Agency), the authority to control hazardous waste in its generation, transportation, treatment, storage and disposal. The Subittle D of RCRA aims at establishing a framework in controlling the management of nonhazardous solid waste.

Hope that it is clear for you. Thank you.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A landfill's leachate collection system is designed and constructed as follows: drainage path (L) = 150...
A landfill's leachate collection system is designed and constructed as follows: drainage path (L) = 150 ft; hydraulic conductivity of the drainage media (k) = 0.01 cm/sec; and slope = 5%. If the leachate impingement rate is 1,000 gallons per acre per day (gpad), what is the maximum head on the liner predicted using the Giroud Equation (inches)?
Given the following design conditions for a Wall form system: Concrete Mix = Type III cement...
Given the following design conditions for a Wall form system: Concrete Mix = Type III cement without retarder, Concrete Unit Weight (w) = 150 pcf Wall height (h) = 10 Feet high, Rate of Pour (R) = 8 Feet per hour, Concrete Temperature (T) = 80 Degrees Fahrenheit, Wall Thickness = 12 inches What is the maximum design pressure on the wall in pounds per square foot (psf)? Please solve with all steps and calculations included.
single choice (   ) Which of the following cover design can be used in the arid...
single choice (   ) Which of the following cover design can be used in the arid regime. A.   Capillary barrier cover consists of a fine-grained soil layer over a coarse-grained soil layer. B.   Store and release cover with cobbles or gravels cover C.   Final cover with surface protection soil layer D.   All of the above (   ) Select insrrect statement about the geosynthetic clay liner (GCL) used in the liner system of a landfill. A.   GCL aims to prevent the...
Design a T Beam for s floor system. Thickness of slab is 75 mm and width...
Design a T Beam for s floor system. Thickness of slab is 75 mm and width of the web is 375 mm, with an effective depth of 600 mm. The beam carries a dead load moment of 270 KN m and a live load moment of 460 KN m. The beam has a span of 5.4 m and has a spacing center to center equal to 1.8 m, fc’ = 20.7 MPa, fy = 345 MPa.
How much should be delivered every x days to minimize the average daily cost in the...
How much should be delivered every x days to minimize the average daily cost in the production cycle between deliveries? Assuming the manufacturer uses raw materials to produce p products each day. Suppose that each delivery of a particular material is $d, whereas the storage of that material is x dollars per unit stored per day. (One unit is the amount required to produce one product).
For the pavement system with the following properties, Design an appropriate structure .for this pavement Top...
For the pavement system with the following properties, Design an appropriate structure .for this pavement Top layer: HMA with E = 400,000 psi, layer coefficient = 0.41., and min thickness 4 inches Intermediate layer: Base coarse with E = 20,000 psi, layer coefficient = 0.10, drainage .coefficient = 0.8, and min. thickness 6 inches Bottom layer: sub-base coarse with E= 10,000 psi, layer coefficient 0.09, and drainage coefficient = 0.8 Subgrade with Mr = 5000 psi If the predicted ESAL...
The minor drainage system collects and conveys runoff from building infrastructures to minimize nuisance flooding. Sometimes,...
The minor drainage system collects and conveys runoff from building infrastructures to minimize nuisance flooding. Sometimes, the downstream turbulence of the hydraulic jump can cause damage and degradation of channel banks. Therefore, drainage design should carry the discharge at nonerosive velocities to minimize the incidents of hydraulic jump and erosion on hydraulic surface. The design and specification of drainage design are conducted based on the Urban Stormwater Management Manual for Malaysia (MSMA 2nd Edition). Lined drains are components of minor...
The minor drainage system collects and conveys runoff from building infrastructures to minimize nuisance flooding. Sometimes,...
The minor drainage system collects and conveys runoff from building infrastructures to minimize nuisance flooding. Sometimes, the downstream turbulence of the hydraulic jump can cause damage and degradation of channel banks. Therefore, drainage design should carry the discharge at nonerosive velocities to minimize the incidents of hydraulic jump and erosion on hydraulic surface. The design and specification of drainage design are conducted based on the Urban Stormwater Management Manual for Malaysia (MSMA 2nd Edition). Lined drains are components of minor...
Accountants should be involved in the detailed design and implementation of the system development life cycle....
Accountants should be involved in the detailed design and implementation of the system development life cycle. Comment on the statement.
A window is designed as shown below (not to scale). The bottom portion has clear glass...
A window is designed as shown below (not to scale). The bottom portion has clear glass and the top portion has colored glass. The colored glass lets in 2323 as much light per unit of area as clear glass. The outside perimeter of the window is 2828 feet. Find the area of the top portion of the window if the window is designed to let in the maximum amount of light. Colored glass (square) Clear Glass Rectangle (connected)
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT