Question

A centrifugal pump has an impeller of outer diameter, 20 cm and outer width,4 cm. The...

A centrifugal pump has an impeller of outer diameter, 20 cm and outer width,4 cm.

The pump delivers a flow of 30 L/s against a head of 10.5 m at an operating speed

of 550 rpm. If the hydraulic efficiency of the pump is 85% and the overall efficiency

is 80%, determine the impeller outlet vane angle and the power required to run the

pump.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Q1/ Centrifugal pump runs at (1200 r.p.m) and the velocity of flow through the impeller is...
Q1/ Centrifugal pump runs at (1200 r.p.m) and the velocity of flow through the impeller is constant (4 m/s). It works with total head of (32m). The vanes are set back at an angle of (30°) at outlet .The outer diameter of the impeller is (600 mm) while the width of outlet is (50mm). Determine 1) work done per second by impeller 2) Vane angle at inlet 3)discharge 4)efficiency
‏A centrifugal pump delivers water against a net head of 14 m and a speed of...
‏A centrifugal pump delivers water against a net head of 14 m and a speed of 1300 rpm. The blade angle is given as 35º. The impeller outlet diameter is 225 mm and outlet width is 50 mm. Determine the discharge of the pump if manometric efficiency is 83%.
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller...
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller with a tangential velocity of 17 ft/sec. If water, @ 68°F, enters the impeller via radial flow (I.E. no whirl), and the inner radius and thickness of the impeller are 1.5-inches. (Assume a constant thickness of the impeller) and if the pump speed is 1750 rpm, with a head loss of 3.5-feet. What is the Torque on the shaft?
1. The diameter of the discharge pipe of a centrifugal pump is 15 cm and the...
1. The diameter of the discharge pipe of a centrifugal pump is 15 cm and the that of the intake pipe is 20 cm The pressure gage connected to the discharge pipe at the pump outlet reads 207 kPa, and the vacuum gage connected to the intake pipe at the pump inlet reads 25 cm of mercury. If the pump discharge is 84.7 L/s and the power needed to run the pump is 35 HP, what is the pump efficiency?
The rotation speed of a centrifugal water pump is 1500 rpm, its flow rate is 15...
The rotation speed of a centrifugal water pump is 1500 rpm, its flow rate is 15 L / s, the rotor diameter is 0.2 m at the outlet, the rotor width at the outlet is 0.01 m and the mechanical efficiency is 0.92. For the fluid entering the rotor in the axial direction, the wing angle is given as 30o at the outlet. What power should be given to the shaft of this pump? (ρwater = 1000 kg / m3)
A centrifugal pump operating at 1800 rpm with an efficiency of 70% discharges 30 L/s against...
A centrifugal pump operating at 1800 rpm with an efficiency of 70% discharges 30 L/s against a 25-m head and requires 10.5 KW, Assuming that the efficiency remains constant, estimate the discharge, head and power if the speed is reduced to 1500 rpm.
1.       A centrifugal pump running at 2950 rpm under test at peak efficiency gave the following...
1.       A centrifugal pump running at 2950 rpm under test at peak efficiency gave the following results: Effective head H= 75m of water, rate of flow Q= 0.05 m3/s, overall efficiency h= 76%. A dynamically similar pump is to operate at a corresponding point of its characteristic when delivering 0.5 m3/s through a pipe 800m long and 1m diameter for which the friction coefficient f =0.05. The pipe discharges 90m above reservoir level. Determine the rotational speed at which the...
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe...
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe has a measured capacity of 0.019 m3/s (water), a suction side vacuum of 20 cm mercury (relative density = 13.6) and a discharge pressure of 240345 N/m2 (gage).  The suction and discharge pipes are at the same elevation.  Assuming that the head loss due to friction is negligible, what is the pump power required
A Francis turbine has the following information: Pressure head supply into turbine HNet = 300 m...
A Francis turbine has the following information: Pressure head supply into turbine HNet = 300 m of water, • Q = 10 m3/s, • N = 400 rev/min, • Runner diameter Drunner = 3m, • Runner inlet width Br = 0.5 m, • Velocity (absolute) at the inlet Vai = 15 m/s, • Draft tube gives 2 m height before water exits, • Overall efficiency ɳo = 80 % Assuming radial outlet and ignore losses across the guide vanes and...
A grey body is one whose absorptivity 1. does not vary with temperature and wavelength of...
A grey body is one whose absorptivity 1. does not vary with temperature and wavelength of the incident ray 2. is equal to its emissivity 3. varies with temperature 4. varies with wavelength of the incident ray A liquid is in equilibrium with its vapor at its boiling point. On an average, the molecules in the liquid and gaseous phases have equal 1. potential energy. 2. kinetic energy. 3.temperature. 4. intermolecular forces of attraction. A liquid of density 1000 kg/m3...