Question

A 30 cm pipe is required for a town’s water supply. As pipes of this diameter...

A 30 cm pipe is required for a town’s water supply. As pipes of this diameter were not available in the market, it was decided to lay two parallel pipes of equal diameter. Find the diameter of the parallel pipes. Assume f is same for all pipes
Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Diameter of parallel pipe=22.73cm

Best of luck ,please hit like

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Consider a pipe that branches out into two parallel pipes and then rejoins at a junction...
Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream. The two parallel pipes have the same lengths and friction factors. The diameters of the pipes are 2 cm and 4 cm. The flow rate in pipe with 2 cm diameter is 10 L/min. Draw piping system What is the flow rate in the other pipe? (L/min) What is the headloss at the junction? Friction factor is 0.001 and the length of the...
The water supply of a building is fed through a main pipe 7.00 cm in diameter....
The water supply of a building is fed through a main pipe 7.00 cm in diameter. A 2.00 cm diameter faucet tap, located 2.10 m above the main pipe, is observed to fill a 25.0 L container in 30.0 s. (a) What is the speed at which the water leaves the faucet? correct answer of 2.65m/s (b) What is the gauge pressure in the 7.00 cm main pipe? (Assume the faucet is the only "leak" in the building.)
Water flowing at 40 L/s through a 9 cm diameter pipe transitions to a 3 cm...
Water flowing at 40 L/s through a 9 cm diameter pipe transitions to a 3 cm diameter pipe. What is the water pressure difference between the pipes? By what factor does the speed of the water increase moving from the larger to smaller pipe?
The water flowing through a 1.7 cm (inside diameter) pipe flows out through three 1.3 cm...
The water flowing through a 1.7 cm (inside diameter) pipe flows out through three 1.3 cm pipes. (a) If the flow rates in the three smaller pipes are 26, 19, and 12 L/min, what is the flow rate in the 1.7 cm pipe? (b) What is the ratio of the speed of water in the 1.7 cm pipe to that in the pipe carrying 26 L/min?
The water flowing through a 2.0 cm (inside diameter) pipe flows out through three 1.4 cm...
The water flowing through a 2.0 cm (inside diameter) pipe flows out through three 1.4 cm pipes. (a) If the flow rates in the three smaller pipes are 24, 15, and 11 L/min, what is the flow rate in the 2.0 cm pipe? (b) What is the ratio of the speed of water in the 2.0 cm pipe to that in the pipe carrying 24 L/min?
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe...
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe has a measured capacity of 0.019 m3/s (water), a suction side vacuum of 20 cm mercury (relative density = 13.6) and a discharge pressure of 240345 N/m2 (gage).  The suction and discharge pipes are at the same elevation.  Assuming that the head loss due to friction is negligible, what is the pump power required
#23)     Water flowing at 40 L/s through a 9 cm diameter pipe transitions to a 3...
#23)     Water flowing at 40 L/s through a 9 cm diameter pipe transitions to a 3 cm diameter pipe. What is the water pressure difference between the pipes? By what factor does the speed of the water increase moving from the larger to smaller pipe?
The water supply of a buidling is fed through a main pipe 6.0 cm in diameter....
The water supply of a buidling is fed through a main pipe 6.0 cm in diameter. A person on the 2nd floor uses a 2.00 cm diameter faucet to fill a 25 L container in 90 seconds. The faucet is 8.00 m above the main line. a) What is the speed at which the water leaves the faucet? b) What is the pressure in the main pipe? (the pressure at the faucet is 1.0 atm)
Water flows through two horizontal pipes that are connected one after another but located at different...
Water flows through two horizontal pipes that are connected one after another but located at different heights. There are pressure gauges on each of the pipes. The speed of the water through the lower pipe is 5.0 m/s. The two pipes have different diameters. The lower pipe has a diameter of 6 cm and the higher one 4 cm. Assume no viscous losses. a. Draw a diagram of the situation and calculate the speed in the upper pipe. b. What...
A 6.8 cm diameter pipe gradually narrows to 4.0 cm. When water flows through this pipe...
A 6.8 cm diameter pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 33.0 kPa and 24.0 kPa, respectively. What is the volume rate of flow?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT