Question

Which one of the followings is not a result of bending moment? Question 14 options: Normal...

Which one of the followings is not a result of bending moment? Question 14 options:

Normal strain

Tensile stress

Normal stress

Shear stress

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Shear stresses may develop along the length of the beam due to; Question 15 options: polar...
Shear stresses may develop along the length of the beam due to; Question 15 options: polar moment of inertia shear stress on the cross-section bending moment maximum normal stress
The slope of the bending-moment diagram is equal to the _______ of the shear-force diagram at...
The slope of the bending-moment diagram is equal to the _______ of the shear-force diagram at that point. Question 1 options: length slope area value Question 2 (2 points) Bending moments are maximum or minimum _______. Question 2 options: where the maximum distributed load is applied at the largest concentrated moment where the shear force diagram is zero where the shear force diagram reaches a maximum Question 3 (2 points) Assuming no external moments are applied to the beam, the...
True false: 1) When subjected to bending, a beam only develops normal stress in tension and...
True false: 1) When subjected to bending, a beam only develops normal stress in tension and compression 2)the shear flow is defined as an average force per unit length for each cross-section. 3)due to bending shear flow develops only along the beam length. 4)) shear center is defined as the point through which force can be applied without causing torsion Fill in the blank: the shear stress induced by bending in a beam is ............ Solve the question problem: A...
1-which one does not correspond to mechanism strengthening? a-alloying or dopping with impurities b-grain-size reduction c-grain...
1-which one does not correspond to mechanism strengthening? a-alloying or dopping with impurities b-grain-size reduction c-grain growth d-strain hardening 2-in polycrystals, the grains with the lowest resolved shear stress always yields firts. true or false 3-resolved shear stress is the result of the application of simple shear stress to a piece of material. true or false 4-decrease on strain hardening? a-percent enlogation b-elastic modulus c-yield strenght d-hardness 5-which term is different from other options? a-strain hardeninh b-dislocation hardening c-cold working...
A critical component of a machine is subject to cyclic loading which produces a bending moment...
A critical component of a machine is subject to cyclic loading which produces a bending moment and stresses that cycle from "0" to a maximum bending stress. The material is steel having a hardness of 160 BHN, Su = 551 Mpa and Sy = 213 Mpa The cross sectional dimensions of the material has a width of 20 mm and a height of 25 mm. The geometry of the part transitions to a larger section through a fillet which has...
Compare the maximum normal stress you calculated in question 5 with the typical tensile and compressive...
Compare the maximum normal stress you calculated in question 5 with the typical tensile and compressive strengths of mortar in Table 4. Comment on the expected failure mechanism for the 4-point bending test. Compare the expected failure mechanism with the actual failure or deformation of the sample you observed in the video (5%). The maximum normal stress calculated in question 5 I got was 3.32MPa. Can you use it to compare to the values of tensile strength and compressive strength...
which one is more important for metal forming and metal machining ,normal stress or shear stress?why?
which one is more important for metal forming and metal machining ,normal stress or shear stress?why?
Question 14 (1 point) Alkanes will NOT undergo which of the following reactions? Question 14 options:...
Question 14 (1 point) Alkanes will NOT undergo which of the following reactions? Question 14 options: cracking addition reforming combustion Question 15 (1 point) What is the smallest member of the alkene family? Question 15 options: methene ethene propene butene Question 16 (1 point) What is the appropriate name for the structure shown? Question 16 options: 1-butene 3-butene 2-butene 4-butyne Question 17 (1 point) The number of known compounds of carbon far exceeds the number of compounds of all other...
Which of the following will result from an increase in return on equity? Question 9 options:...
Which of the following will result from an increase in return on equity? Question 9 options: A) Decrease in fixed costs B) Decrease in cash on the balance sheet C) Increase in the tax rate D) Increase in fixed costs
Which of the following is not a prerequisite for a Eurocurrency centre? Question 14 options: 1)...
Which of the following is not a prerequisite for a Eurocurrency centre? Question 14 options: 1) A favourable environment, which is conducive to the smooth conduct of international finance. 2) Good telecommunication systems. 3) Political stability. 4) A European location. 5) None of the given answers
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT