Question

The results for five (5) specimens are presented below. Get the average compressive strength of the...

The results for five (5) specimens are presented below. Get the average compressive strength of the mix design in psi.

load (lb) dia (in)
125523 6
128065 6
125400 6
125742 6
125092 6

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A concrete masonry unit is tested for compressive strength and produces the following results: Failure load...
A concrete masonry unit is tested for compressive strength and produces the following results: Failure load = 100000 lb Gross area = 170 in2 Gross volume = 960 in3 Net volume = 836 in3 Please round to the nearest hundredth (i.e., 0.01). 1. What is the percentage of net cross-sectional area? = Answer % 2. Is the unit categorized as solid or hollow? Write down either solid or hollow. No spaces, and case is unimportant. Answer 3. What is the...
A concrete masonry unit is tested for compressive strength and produces the following results:             Failure load...
A concrete masonry unit is tested for compressive strength and produces the following results:             Failure load = 120,000 lb             Gross area = 130 in2             Gross volume = 960 in3             Net volume = 447 in3 Is the unit categorized as solid or hollow? Why? What is the compressive strength? Does the compressive strength satisfy the ASTM requirements for load bearing units shown in Table 8.2?
Aconcrete mixture for a proposed building work is to be designed. A characteristic compressive strength of...
Aconcrete mixture for a proposed building work is to be designed. A characteristic compressive strength of 25 MPa with 5% defective rate is specified for 28 days. The standard deviation may be taken based on a compressive strength results on specimens less than 20. A slump of 40 mm is required and the maximum w/c ration and the minimum cement content allowed are 0.7 and 200 kg/m3, respectively. The fine aggregate is uncrushed and the percentage passing sieve 600 Micro...
Strength of concrete: The compressive strength, in kilopascals, was measured for concrete blocks from five different...
Strength of concrete: The compressive strength, in kilopascals, was measured for concrete blocks from five different batches of concrete, both three and six days after pouring. The data are as follows. Can you conclude that the mean strength after three days is greater than the mean strength after six days? Let μ1 represent the mean strength after three days and =μd−μ1μ2. Use the =α0.01 level and the P-value method with the TI-84 Plus calculator. Block 1. 2 3. 4. 5...
The cooling system in a nuclear submarine requires the specifications that the average weld strength must...
The cooling system in a nuclear submarine requires the specifications that the average weld strength must meet or exceed 150 psi for proper coolant circulation. A random sample of 36 welds results in x ̅=157 psi and s=15 psi. A design engineer wants to test the specifications based on the sample information at 5% level of significance. Complete the hypothesis test by answering the following questions. State the hypotheses. Calculate the test statistic. What is/are the critical value(s)? What is...
5. A manufacturer of college textbooks is interested in estimating the strength of the bindings produced...
5. A manufacturer of college textbooks is interested in estimating the strength of the bindings produced by a particular binding machine. Strength can be measured by recording the force required to pull the pages from the binding. If this force is measured in pounds, how many books should be tested in order to estimate with 95% confidence to within 0.1 lb the average force required to break the binding? Assume that  is known to be .8 lb. 6. We...
Use the total cost(TC) schedule that is presented in the the table below to calculate average...
Use the total cost(TC) schedule that is presented in the the table below to calculate average total cost, average variable cost, average fixed cost and marginal cost when output (Q) is equal to 6 Q TC 0 5 1 7 2 8 3 10 4 14 5 20 6 28 7 38 8 50 9 72
In the probability discussion post, you were presented with two options:, the post is reproduced below:...
In the probability discussion post, you were presented with two options:, the post is reproduced below: o “ Suppose you're offered two chances to win money based on a simple coin flip: ▪ Option 1: If the coin lands heads, you get $5. If it lands tails, you lose $2. ▪ Option 2: If the coin lands heads, you get $15,000. If it lands tails, you lose $6,000.” • The expected value of Option 1 turned out to be +$1.50,...
For exercise prescription: Ms. Case Study-WM is a 48-year-old woman who works 5 days per week...
For exercise prescription: Ms. Case Study-WM is a 48-year-old woman who works 5 days per week as a bank executive. She previously walked up the stairs to her third floor office but has started to use the elevator because, in the past month, she has experienced shortness of breath when walking up the stairs. The patient was physically active throughout college as a club lacrosse player but has not exercised regularly since she gave birth to her children who are...
Item 1 In the case below, the original source material is given along with a sample...
Item 1 In the case below, the original source material is given along with a sample of student work. Determine the type of plagiarism by clicking the appropriate radio button. Original Source Material Student Version I accept the point that whenever learning occurs, some medium or mix of media must be present to deliver instruction. However, if learning occurs as a result of exposure to any media, the learning is caused by the instructional method embedded in the media presentation....