Question

A pump is used to deliver water from a large reservoir to another large reservoir that...

A pump is used to deliver water from a large reservoir to another large reservoir that is 20 m higher.

The inlet of the pipe is submerged in the one reservoir and the exit is just above the surface of the other reservoir. If the friction head loss in the 200-mm-diameter, 4-km-long pipeline is 2.5 m for every 500 m of pipe length, determine the required power output of the pump so the flow is 0.6 m3/s.

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A pump delivers water (r= 1000 kg/m3, µ= 0.860x10-3 kg/m·s) from one reservoir to another reservoir...
A pump delivers water (r= 1000 kg/m3, µ= 0.860x10-3 kg/m·s) from one reservoir to another reservoir through 120 m of 0.05 m diameter pipe. Volumetric flow rate in the pipe line is measured with venturi meter. Throat diameter of venturi meter is 38 mm and pressure drop in the venturi meter is 156.9 kPa.The surface of the pipe is rough e/D=0.0001. Calculate the power of the pump required for the water–transfer. See the figure below for several pipe– fittings installed...
A pump needs to move water from a lower reservoir to an upper reservoir at a...
A pump needs to move water from a lower reservoir to an upper reservoir at a rate of 600 cfs through a 9,000 ft long, 6-ft diameter pipeline (f = 0.03). For a 1,500 ft change in water surface elevation between the lower and upper reservoirs, compute the needed power input to the pump assuming a pump efficiency of 75% and that minor losses are negligible. In addition, compute the needed power input to the corresponding motor assuming the motor...
Water flows at a velocity of 4.2 m/s from one reservoir (z = 41.5 m) to...
Water flows at a velocity of 4.2 m/s from one reservoir (z = 41.5 m) to another reservoir (z = 8.0 m) over a 1011-m long, 300-mm diameter pipeline. If the total head loss is 19 times the velocity head, determine the power (in N-m/s) extracted by a turbine (z = 8.0 m) located between the reservoirs. Assume γ = 9790 N/m3. Select one: a. 4.772e4 b. 8.555e4 c. 6.075e4 d. 8.224e4
A pump is used to carry water (T =60 oF and ν = 1.217×10-5 ft2/s) from...
A pump is used to carry water (T =60 oF and ν = 1.217×10-5 ft2/s) from a large tank (elevation of surface = 30 ft and at atmospheric pressure) through a pipe to the exit (elevation 60 ft) at a rate Q = 1.5 cfs as shown below. The pipe is made of cast iron (ε = 0.00085 ft). The pipe segment before the pump has length L = 500 ft (three horizontal sections of 160 ft each and two...
A steel pipeline conveys water (density 1000 kg/m3 , bulk modulus 2.05x109 N/m2 ) from an...
A steel pipeline conveys water (density 1000 kg/m3 , bulk modulus 2.05x109 N/m2 ) from an upper to a lower reservoir the pipeline material is steel with Young’s modulus 210x109 N/m2 . It is 611 m long, has an internal diameter 1.1m, wall thickness 25 mm and surface roughness 0.68 mm. The flow is controlled by a valve located at the entrance to the lower reservoir, 211 m below the surface level in the upper reservoir. (a) Under steady flow...
An industrial pump is to be used to supply water from Lake Bonno to an agricultural...
An industrial pump is to be used to supply water from Lake Bonno to an agricultural field located 500 m away from the lake, and at an elevation of 20 m above the surface of the lake. If the horse-power of the pump is 45-hp, what is the discharge that can be delivered by using a pipe of diameter D = 0.4 m and a friction coefficient of f = 0.015? Neglect all minor losses. Is the flow laminar or...
The characteristics of a centrifugal pump that is used to pump water (998 kgm-3 , 1.14×10-3...
The characteristics of a centrifugal pump that is used to pump water (998 kgm-3 , 1.14×10-3 Nsm-2 ) from one reservoir to another are given in the table below. The difference between the water levels is 3 m. A 840 m long, 0.15 m diameter pipe with absolute roughness of 6×10-6 m joins the two reservoir. Determine the (a) best efficiency point, (b) operating point, (c) operating efficiency and the (d) power adsorbed when the average velocity in the pipe...
A high-head hydroelectric scheme consists of a reservoir from which the water is delivered to four...
A high-head hydroelectric scheme consists of a reservoir from which the water is delivered to four Pelton turbines through a low pressure tunnel LT = 10 km long, 4 m in diameter, lined with concrete. The tunnel splits into four steel pipelines (penstocks) 500 m long, 2 m in diameter each terminating in a single nozzle, the area of which is varied by a spear valve. The maximum diameter of each nozzle is 0.9 m. The difference in level between...
A house is situated 20 m above the datum. It has to be supplied water from...
A house is situated 20 m above the datum. It has to be supplied water from nearby reservoir. The pipe length from the reservoir to the house is 200 m, diameter is 30 cm, flow has to be 0.2 m3/s. Friction loss allowed is 5+Z m and the pressure to be maintained in the pipe in the house is 20 kN/m2. Also consider minor losses (entrance and outlet). Calculate the height the reservoir has to be situated above the datum?...
5.0kg/s cyclohexane is pumped from a height of 2.5m to a height of 15m. Before the...
5.0kg/s cyclohexane is pumped from a height of 2.5m to a height of 15m. Before the pump inlet, the cyclohexane is motionless inside of a holding tank. The diameter of the pipe at the exit point is 2.5 cm. The density of cyclohexane is 779 kg/m3 . Calculate the pump power required in watts and hp. Assume negligible friction. Hint: you will have to include the effect of the outlet velocity ​​
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT