Question

A curve of radius 140 m and e= 0.08 is located at a section of an...

A curve of radius 140 m and e= 0.08 is located at a section of an existing rural highway, which restricts the safe speed at this section of the highway to 60% of the design speed. This drastic reduction of safe speed resulted in a high crash rate in this section. To reduce the crash rate, a new alignment is to be designed with a horizontal curve. Determine the minimum radius of this curve if the safe speed should be increased to the design speed of the highway. for the existing curve, and the new curve is to be designed with e= 0.08

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The existing posted speed limit on a section of highway is 88 km/h and studies have...
The existing posted speed limit on a section of highway is 88 km/h and studies have shown that the current 85th percentile speed is 104 km/h. If the posted speed limit is to be increased to the current 85th percentile speed, what should be the increase in the radius of a curve that is just adequate for the existing posted speed limit? Assume a superelevation rate of 0.08 for the existing curve and for the redesigned curve.
A horizontal curve of radius 5620 ft is designed for 60 mph. The roadway is a...
A horizontal curve of radius 5620 ft is designed for 60 mph. The roadway is a 4-lane undivided highway with 12-ft lanes. A tree is located on the inside of the curve only 42 ft from the center of the road. Does it pose a stopping sight distance problem for the drivers travelling at the design speed? Show all supporting calculations.
A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station...
A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station 10+00 and PT at station 13+70. The central angle is 25 degrees, the superelevation is 4%, and 40 ft of clearance is available between an obstruction and the centerline. Determine the maximum safe design speed to the nearest 5 mph.
A horizontal curve is being designed for a new four-lane roadway with 11-ft lanes. The PT...
A horizontal curve is being designed for a new four-lane roadway with 11-ft lanes. The PT is located at station 1050+20, the design speed is 45 mph and maximum superelevation of 4%. If the central angle of the curve is 30 degrees, what is the radius of the curve and location of the PC and PI?
Determine the minimum length of a vertical curve necessary for it to be adequate, under the...
Determine the minimum length of a vertical curve necessary for it to be adequate, under the visibility criteria for braking, for a design speed of 80 mph. The slopes corresponding to the PVC and PVT of the curve in question are 4% and -3% respectively. the PVI station is 120 + 70 and its elevation is 810 meters. The coefficient of lateral friction is 0.08. All circular curves in the segment under study have been designed using an 8% superelevation...
Question 4 4.1 A 2-lane road has a circular curve with a radius of 210 m,...
Question 4 4.1 A 2-lane road has a circular curve with a radius of 210 m, curve length of 300 m. The lane width and shoulder width are 3.6 and 1.8 m, respectively. The design speed on the road section is 80 km/h and minimum required SSD is 115 m. Determine the minimum acceptable distance of a building structure from the edge of the road. (4) 4.2 An 80 km/h rural road section has a three-leg intersection. Assume a WB50...
1. A horizontal curve on a two-lane highway is designed with a 2000 ft radius, 12...
1. A horizontal curve on a two-lane highway is designed with a 2000 ft radius, 12 ft lanes, and 60mph design speed. Determine the distance that must be cleared from the inside edge of the inside lane to provide a sufficient stopping sight distance. 2, A flexible pavement is constructed with 102 mm (4 inches) of hot mix asphalt (HMA) wearing surface, 203 mm (8 inches) of emulsion/aggregate-bituminous base, and 203 mm (8 inches) of crushed stone subbase. The subgrade...
Please answer the following Case analysis questions 1-How is New Balance performing compared to its primary...
Please answer the following Case analysis questions 1-How is New Balance performing compared to its primary rivals? How will the acquisition of Reebok by Adidas impact the structure of the athletic shoe industry? Is this likely to be favorable or unfavorable for New Balance? 2- What issues does New Balance management need to address? 3-What recommendations would you make to New Balance Management? What does New Balance need to do to continue to be successful? Should management continue to invest...
In February 2012, the Pepsi Next product was launched into the US market. This case study...
In February 2012, the Pepsi Next product was launched into the US market. This case study provides students with an interesting insight into PepsiCo’s new product process and some of the challenging decisions that they faced along the way. Pepsi Next Case Study Introduction Pepsi Next was launched by PepsiCo into the US market in February 2012, and has since been rolled out to various international markets (for instance, it was launched in Australia in September 2012). The new product...
Using the model proposed by Lafley and Charan, analyze how Apigee was able to drive innovation....
Using the model proposed by Lafley and Charan, analyze how Apigee was able to drive innovation. case:    W17400 APIGEE: PEOPLE MANAGEMENT PRACTICES AND THE CHALLENGE OF GROWTH Ranjeet Nambudiri, S. Ramnarayan, and Catherine Xavier wrote this case solely to provide material for class discussion. The authors do not intend to illustrate either effective or ineffective handling of a managerial situation. The authors may have disguised certain names and other identifying information to protect confidentiality. This publication may not be...