Question

Two gears have pitch of 4mm . The number of teeth on gear 1 is 40...

Two gears have pitch of 4mm . The number of teeth on gear 1 is 40 on gear 2 is 24 . if the gear 2 rotates at 600 rpm , determine the velocity of sliding when the contact is at the tip of tooth at gear 2. Take addendum equal to on module . in addition find the maximum velocity of sliding. The angle of two gear is 20.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Two standard gears have 18 and 32 teeth, respectively. The diametral pitch is 10, and the...
Two standard gears have 18 and 32 teeth, respectively. The diametral pitch is 10, and the pinion rotates at 1000 rpm. Determine the following: (a) center distance, (b) pitch diameters, (c) circular pitch, (d) pitch line velocity, (e) angular velocity of the gear.
A 2.5 teeth/in diametral pitch 17‐tooth pinion and 50 tooth gear are paired. The gears are...
A 2.5 teeth/in diametral pitch 17‐tooth pinion and 50 tooth gear are paired. The gears are cut on the 20 degrees ̊full‐depth involute system. Find the contact ratio.
Design a gear train that satisfies the following requirements: - Comprised of four (4) spur gears...
Design a gear train that satisfies the following requirements: - Comprised of four (4) spur gears (g1, g2, g3, g4) where the input (g1) and output (g4) gears rotate in the same directions. - The angular velocity of the input gear (g1) is equal to 400 RPM. - The angular velocity of the output gear (g4) is equal to 25 RPM. - The gear ratio between any two meshing gears cannot be greater than 4:1 or less than 1:4. -...
find the gear ratio, circular pitch ,base pitch,pitch diameters,pitch radii,centre distance , addendum,dedendum,whole(total)depth, clearance, outside diameters,length...
find the gear ratio, circular pitch ,base pitch,pitch diameters,pitch radii,centre distance , addendum,dedendum,whole(total)depth, clearance, outside diameters,length of path of contact ,length of Arc of contact,and contact ratio of gear set with given parameters .If the centre distance is increased by 2%,what is the new pressure angle and increase in backlash?Given a 0.2344 pd ,20° pressure angle,19 tooth pinion is meshed with a 37 tooth gear.Assume the tooth forms are standard proportions of gear systems depth involute profiles
###HELICAL GEAR### A turbine at 30 000 rpm is used to drive a reduction gear delivering...
###HELICAL GEAR### A turbine at 30 000 rpm is used to drive a reduction gear delivering 3hp at 3000 rpm.the gears are 20° involute herringbone gears of 28 pitch and 2 1/8 in. effictive width....the pinion has 20 teeth with a helix angle of 23°. Determine the load normal to the tooth surface.
MATHEMATICS 1. The measure of location which is the most likely to be influenced by extreme...
MATHEMATICS 1. The measure of location which is the most likely to be influenced by extreme values in the data set is the a. range b. median c. mode d. mean 2. If two events are independent, then a. they must be mutually exclusive b. the sum of their probabilities must be equal to one c. their intersection must be zero d. None of these alternatives is correct. any value between 0 to 1 3. Two events, A and B,...
  The following balance sheet and income statement should be used for questions #1 through #6: Kuipers,...
  The following balance sheet and income statement should be used for questions #1 through #6: Kuipers, Inc. 2001 Income Statement (OMR in millions) Net sales 9,625 Less: Cost of goods sold 5,225 Less: Depreciation 1,890 Earnings before interest and taxes 2,510 Less: Interest paid 850 Taxable income 1,660 Less: Taxes 581 Net income 1,079 Addition to retained earnings 679 Dividends paid 400 Kuipers, Inc. 12/31/00 and 12/31/01 Balance Sheet (in OMR, in millions) 2000 2001 2000 2001 Cash 1,455 260...
111.C.1: How Well Do I Respond to Turbulent Change? Instrument Listed to the right are a...
111.C.1: How Well Do I Respond to Turbulent Change? Instrument Listed to the right are a set of statements describing characteristics in a managerial job. If your job had these features, how would you react to them? Use the following rating scale for your answers: his feature would be very unpleasant for me This feature would be somewhat unpleasant for me I'd have no reaction to this feature one way or another; or it would be about equally enjoyable and...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT