Question

When altering the area and young's modulus units of a concrete beam. Why will this not...

When altering the area and young's modulus units of a concrete beam. Why will this not change the bending moment and shear force diagram, from the original result?

Homework Answers

Answer #1

solution:-

  • upon changing area(A) and young's modulus (E) it will not lead to change in shear force diagram and Bending moment diagram.
  1. Because shear force diagram is a diagram that represents the variation of shear force along the length of beam and only depends on the loading and doesn't depend on the area, young's modulus of the beam.
  2. and bending moment diagram is variation of moment along the length of the beam and it also doesn't depend on the area and Young's modulus of the beam.
  • FOR EXAMPLE
  • IF you take a simply supported beam with uniformly distributed load.

​​​​​​​

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Q3: Bending moment and shear force diagrams were plotted for a cantilever beam of span 10...
Q3: Bending moment and shear force diagrams were plotted for a cantilever beam of span 10 m when subjected to a uniformly distributed load of magnitude ‘w’ kN/m over the entire span, two concentrated loads ‘2w’ kN at a distance 3 m from the free end and ‘3.5w’ kN at a distance 4.5 m from the free end respectively. It was observed that the value for maximum bending moment acting on the beam is equal to (-175 kNm). Suggest a...
Determine the largest allowable bending moment for a rectangular reinforced concrete beam having the width b...
Determine the largest allowable bending moment for a rectangular reinforced concrete beam having the width b = 200 mm, total height h = 375 mm and the distance from the bottom surface of the beam to the centre line of steel bars = 75 mm. Use the total area of steel As = 1360 mm2, modulus of elasticity of concrete = 30 GPa, modulus of elasticity of steel = 210 GPa, allowable compressive stress for concrete = 15 MPa and...
The slope of the bending-moment diagram is equal to the _______ of the shear-force diagram at...
The slope of the bending-moment diagram is equal to the _______ of the shear-force diagram at that point. Question 1 options: length slope area value Question 2 (2 points) Bending moments are maximum or minimum _______. Question 2 options: where the maximum distributed load is applied at the largest concentrated moment where the shear force diagram is zero where the shear force diagram reaches a maximum Question 3 (2 points) Assuming no external moments are applied to the beam, the...
overhanging beam is simply supported at san of 13m and carries of point load of 4000N...
overhanging beam is simply supported at san of 13m and carries of point load of 4000N 3m from right support the left overhangs is 3 m away from left support and has a point load of 5000N. the right overhang is of 4m carrying UDL of 200N per meter for entire rightover . draw shear force and bending moment diagram . calculate the maximum bending moment.
reinforced concrete beam if increasing the area of steel would increase the beam strength why we...
reinforced concrete beam if increasing the area of steel would increase the beam strength why we don't do that? Explain and show graph drawing
A ruler is accurate when the temperature is 26.7 °C. When the temperature drops to -12.3...
A ruler is accurate when the temperature is 26.7 °C. When the temperature drops to -12.3 °C, the ruler shrinks and no longer measures distances accurately. However, the ruler can be made to read correctly if a force of magnitude 1.72 x 103 N is applied to each end so as to stretch it back to its original length. The ruler has a cross-sectional area of 1.39 x 10-5 m2, and it is made from a material whose coefficient of...
So, why can a properly executed karate kick break a concrete block without fracturing bones [16]?...
So, why can a properly executed karate kick break a concrete block without fracturing bones [16]? First, bone is a very strong material. Its ultimate compressive strength is approximately 40 times larger than concrete. Second, contact is made with the edge of the foot. This concentrates the force into a small area of the target and reduces the likelihood of bending a bone to the point of fracture. Third, the collision with the target is essentially inelastic and extends over...
Experimental data: Length L0 of the cold rod (measured with a meter stick): 600 +/- 1...
Experimental data: Length L0 of the cold rod (measured with a meter stick): 600 +/- 1 mm Cross-sectional diameter d of the rod (measured with a caliper): 6.1 +/- 0.1 mm The change in length ∆L after the rod reached its final temperature: 1.04 +/- 0.01 mm The initial temperature of the rod (the room temperature): 22 +/- 1 ̊C The final temperature of the rod shown by the thermometer: 93 +/- 1 ̊C Linear thermal expansion coefficient calculation: 1)...
3.Explain why if a CD power supply is used, only when the power supply is turned...
3.Explain why if a CD power supply is used, only when the power supply is turned on or of there is an induced current in the second coil (secondary). 4. Explain why when the switch is on, and there is a direct current through the circuit, there is no induced electric current in that coil. Electromagnetic Induction I. Objectives 1.   Verify the Faraday-Lenz‘s Law 2. Perform measurements with a set of coils to understand how a transformer works. II. Theory In...
What tools could AA leaders have used to increase their awareness of internal and external issues?...
What tools could AA leaders have used to increase their awareness of internal and external issues? ???ALASKA AIRLINES: NAVIGATING CHANGE In the autumn of 2007, Alaska Airlines executives adjourned at the end of a long and stressful day in the midst of a multi-day strategic planning session. Most headed outside to relax, unwind and enjoy a bonfire on the shore of Semiahmoo Spit, outside the meeting venue in Blaine, a seaport town in northwest Washington state. Meanwhile, several members of...