Question

Length of soil sample for constant head permeability test is 30 cm, Area of specimen is...

Length of soil sample for constant head permeability test is 30 cm, Area of specimen is 177cm2, constant head difference is 50 cm, total volume of water collected in 5 min is 350003. Calculate the hydraulic conductivity of the soil. A) 2.85 x 103cm/sec D) 1.09 x 102cm/sec B) 1.09 x 10" art/sec C) 3.95 x10' cm/sec

Homework Answers

Answer #1

By substituting the above data we get K = 3.95 cm/sec ie. None of the option is matching.

If we take vol. V = 35000 cm^3 then we are getting K = 0.395 cm/sec = 3.95 X 10^-1 cm/sec ie. Option C is matching.

I request you to please check the data given in the question.

If you found it useful please rate the solution.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
(a) A constant head permeability test was performed for the soil specimen. The sample length was...
(a) A constant head permeability test was performed for the soil specimen. The sample length was 90 mm and sample diameter was 75 mm. The total head loss across the sample was measured to be 635 mm. The flow rate was measured and it took 278 seconds to fill up a 1-litre beaker. Estimate the coefficient of permeability (k), in m/s, based on results of the constant head test. (b) If a falling head test was conducted on the same...
Both falling head and constant head permeability tests are common experiments to obtain soil sample hydraulic...
Both falling head and constant head permeability tests are common experiments to obtain soil sample hydraulic conductivity. Please provide 3 recommendations for each experiment to improve their accuracy of test results.
Q1. A standard constant head permeability test was performed on a coarse sand soil sample that...
Q1. A standard constant head permeability test was performed on a coarse sand soil sample that was 100 mm in diameter and 200 mm in length. The measured discharge through the sample was 2.16 litres per minute with an equivalent constant head loss of 845 mm (acting over the entire sample length). At the end of the test, the total mass of the sample was recorded 3.142 kg and the moisture content of the sample was measured at 24 %....
Give a definition of Permeability test List the Equipments and tools needed to perform the costant...
Give a definition of Permeability test List the Equipments and tools needed to perform the costant Head Test A Test was Performed according to the following data Volume of specimen, V = ?=??2L (cm2) . 418.03 Specific gravity of soil solids, Gs 2.66 Mass of specimen tube with fittings, (g) 238.4 Mass of tube with fittings and specimen, W2 (g) Dry density of specimen, 9653 Void ratio of specimen, 0.53 (Note: pw = 1 g/cm3) ■ If K=QL/Aht (cm/s) and...
A Test was Performed according to the following data: Volume of specimen, V = ? =...
A Test was Performed according to the following data: Volume of specimen, V = ? = ?? 2 L (cm2 ) . 418.03 Specific gravity of soil solids, Gs 2.66 Mass of specimen tube with fittings, (g) 238.4 Mass of tube with fittings and specimen, W2 (g) Dry density of specimen, 9365 Void ratio of specimen, 0.53 (Note: pw = 1 g/cm3 If K=QL/Aht (cm/s) and Gs =2.66 , Volume of Specimen is 418.03 cm3 Determination of coefficient of permeability...
A sample of fine sand having a length of 60 mm and a cross sectional area...
A sample of fine sand having a length of 60 mm and a cross sectional area of 50 cm2 was tested under constant head conditions. The height of the water head during the test was 40 cm. A total of 430 mL of water was collected in 10 minutes. Calculate the discharge velocity (v). Report your answer in terms of cm/sec
A soil sample is 10 cm in diameter and 1 m long. The sample is oriented...
A soil sample is 10 cm in diameter and 1 m long. The sample is oriented vertically in a tube. The tube in which the soil resides is 2.5 m tall. The lower 1 m is occupied by the soil, and there is 1 m of water ponded on top of the soil. A float valve keeps the amount of water ponded on the soil at 1 m. Water drips out the bottom of the soil specimen such that the...
A tensile test sample has a gauge length of 10 cm and a cross-section area of...
A tensile test sample has a gauge length of 10 cm and a cross-section area of 500 mm2. During the test, the sample yields at 0.2 % strain under a load of 1.5 x 105 N and the corresponding gauge length is 10.1 cm. The maximum load of 2 x 105 N is reached at a gauge length of 13 cm and the fracturing cross-section area is 370 mm2. Determine the values of (a) yield strength, (b) modulus of elasticity,...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT