Question

2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...

2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. Assuming no permanent deformation occurred in that material, what is the modulus of elasticity?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length...
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length 20 cm. While applying a load of 10 kN, there will be an extension of 0.012 cm on a length of 20 cm. Maximum load carried by the rod was found to be 26 kN and the load beyond which stress is not proportional to strain was observed to be 11 kN. When the specimen breaks, the extension of the rod for 20 cm...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 150 N and thermal loading which imposes a longitudinal force of 230 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.5 mm in length at both ends and decreasing by 0.0125 mm at...
A rod has a square cross section of (5 x 5) mm. length of the rod...
A rod has a square cross section of (5 x 5) mm. length of the rod is 120 cm. The allowable stress is 400 MPa. After applying the load (F), square section changes to (4.95 x 4.95) mm. 1. What is the type of the load (F), is it tension or compression? 2. What is the longitudinal strain in steel rod? 3. What is the modulus of elasticity of the material of the rod? 4. What is the value of...
Problem 1: A round bar with a diameter of 32 mm, and 4012 mm in length...
Problem 1: A round bar with a diameter of 32 mm, and 4012 mm in length was under tensile test to determine the mechanical properties of the material. The following table shows the load versus strain data collected from the testing machine and a strain gauge applied on the bar in the loading direction. The measured percentage elongations were 19.8 % and 14.6 % on gauge lengths of 100 mm and 200 mm respectively. Assume: the elongations include the necking;...
Please answer all four questions. Thank you! 1) A tensile load of 71,000 pounds is applied...
Please answer all four questions. Thank you! 1) A tensile load of 71,000 pounds is applied to a square steel bar that is 0.75 inches in cross section dimension and has a gage length of 6.5 inches. Under this load what is the longitudinal elongation? 2) Write the 2 equations for steel corrosion as its iron changes from that of fresh steel to fully corroded ferric oxide. 3) A square cross-section piece of metal is put under tensile stress. The...
Commercial hose connectors used for watering and irrigation are sold in variety of sizes and shapes....
Commercial hose connectors used for watering and irrigation are sold in variety of sizes and shapes. The cost of such connector depends on the cost of material from which it is made and some other design limitations. Using the following information: Tensile load imposed on the connector is 20,000 N. Deformation of the connector is purely elastic. Outer diameter (OD) of the connector is 20 mm. Length of the connector is 30 mm. Inner diameter (ID) of the connector is...
A log 2 m in diameter and 12 m long is towed at a constant speed...
A log 2 m in diameter and 12 m long is towed at a constant speed of 3 m/s in fresh water at 20oC. What is the drag force, in kN, on this log if it is towed lengthwise (water facing log end), what is the required towing power in kW, and what would the drag force be in kN if the log was towed widthwise (water facing log length) ?
A rod 2 m long, 2 cm in diameter and 5 kg in mass is fixed...
A rod 2 m long, 2 cm in diameter and 5 kg in mass is fixed at one end and is stricken by a force F to produce a 3rd overtone and elongates at 1 cm. A string of length L and mass 750 grams is puled by a T = 30 to produce a 3rd harmonic frequency. Determine the force F and length L that produces the same value of frequencies in the two materials, if the sound wave...
Materials lectures: 1- A wire 0.00108 m in diameter and 1.5 m in length is used...
Materials lectures: 1- A wire 0.00108 m in diameter and 1.5 m in length is used to support a load of 37 kg. The wire increases in length by 0.00088 m. To 3 significant figures, what is Young's Modulus of the wire in SI units of force per area? (answer: 6.75e11 N/m^2) 2- The atmospheric pressure above a fresh water lake is 101.2 kPa. What is the pressure in pascals at 12.1 m below the surface? (answer: 2.20e5 Pa) 3-...
1. A steady horizontal force F of magnitude 100 N is applied at the axle of...
1. A steady horizontal force F of magnitude 100 N is applied at the axle of a solid disk as shown. The disk has mass of 5.0 kg and a diameter of 0.40m. Calculate the linear speed of the center of the disk after it has moved 10m. (moment of inertia is 1/2 Mr^2) I have the answer as 16 m/s. 2. A solid sphere of a radius 0.2 m is released from rest from a height of 2.0 m...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT