Question

Which will support more load when used as a building column: 1) A 6" x 6"...

Which will support more load when used as a building column:
1) A 6" x 6" (actual size) wood ( Douglas Fir) post 16 feet long, pinned at both ends

or


2) A structural steel W10 x 39 I-beam 20 feet long, pinned at the ends

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A column is to be used to support a critical vertical load of 6000 kN. The...
A column is to be used to support a critical vertical load of 6000 kN. The column is 6 m long and having pin at one end and fixed at another end and restrained in weak axis. Modulus of Elasticity (E) of structural steel is 200,000 MPa. Suggest Most suitable UC from manufacture’s catalogue . Unsupported length of column = 6m
An A992 W21×111 is used as a column in a building to support a dead load...
An A992 W21×111 is used as a column in a building to support a dead load of 120 kips and a live load of 300 kips. The column effective length is 22 ft for the y-axis and 33 ft for the x-axis. Determine whether the column will support the load by LRFD.
A 10-foot long, 4x6 column of No. 1 Douglas-Fir Larch supports a factored load of 25,000...
A 10-foot long, 4x6 column of No. 1 Douglas-Fir Larch supports a factored load of 25,000 pounds. The column is pin supported at both ends, but is otherwise laterally unbraced. The column is dry in-use, is not incised, and is subject to normal temperatures. Assuming the governing load combination is (1.2D+1.6Lr), determine whether or not this column is adequate to support the factored load. In your analysis, assume bearing perpendicular to grain does not apply
An axially loaded 10’ long 2”x 6” S4S Douglas Fir stud is pinned at both ends....
An axially loaded 10’ long 2”x 6” S4S Douglas Fir stud is pinned at both ends. E= 1.4 x 106 psi Allowable compressive stress parallel to the grain = 825 psi For the strong axis: What load will cause buckling? If the weak axis were braced every 30” what is the critical buckling load about the weak axis? Neglecting buckling, what is the maximum load that can be applied to the stud before it will be crushed? What would be...
A simply Supported Steel "I Beam" is made of three 1" x 7" plates with a...
A simply Supported Steel "I Beam" is made of three 1" x 7" plates with a mass of 898.4 lbm each as shown below. Steel has a modulus of elasticity of 30x10^6 psi. The beam is allowed to deflect 1.10 in. The length of the beam L between supports is 10.5 feet. a) If i turn the same beam clowise 90 degrees, what percentage of the problem 20 maximum load can i apply to yield the same 1.10 inch deflection?...
A 6-3/4 in. x 21 in. 24F-1.7E softwood glulam is used to support equal point loads...
A 6-3/4 in. x 21 in. 24F-1.7E softwood glulam is used to support equal point loads at the third point of a 33 ft simply supported span. The controlling LRFD load combination is 1.2D + 1.6Lr + L, the moisture content will exceed 16% in service, and the beam is exposed to normal temperatures. Lateral support is provided at the supports and at the third point. Determine the adjusted nominal moment capacity M’n based on the volume factor.
1. (a) Explain the difference between columns which are short and slender and those which are...
1. (a) Explain the difference between columns which are short and slender and those which are braced and unbraced. (b) Calculate the ultimate axial load capacity of a short-braced column supporting an approximately symmetrical arrangement of beams assuming that it is 500 mm square and is reinforced with eight 20 mm diameter bars. Assume that fcu = 40 N/mm2, fy = 500 N/mm2 and the concrete cover is 25 mm. Design the shear reinforcement for the column. 2. (a) A...
MATHEMATICS 1. The measure of location which is the most likely to be influenced by extreme...
MATHEMATICS 1. The measure of location which is the most likely to be influenced by extreme values in the data set is the a. range b. median c. mode d. mean 2. If two events are independent, then a. they must be mutually exclusive b. the sum of their probabilities must be equal to one c. their intersection must be zero d. None of these alternatives is correct. any value between 0 to 1 3. Two events, A and B,...
1. Which is statement is true? I. A single-price monopolist charges a price equal to the...
1. Which is statement is true? I. A single-price monopolist charges a price equal to the marginal cost of the last unit sold. II. A monopolist with positive marginal costs and facing a linear demand curve always sets a quantity (or price) such that it sells on the elastic section of the demand curve. III. A monopolist regulated by marginal-cost pricing regulation sells at a price that covers its variable and fixed costs of production, but it still causes a...
1. Electronic blood pressure devices require the use of a stethoscope. * a. True b. False...
1. Electronic blood pressure devices require the use of a stethoscope. * a. True b. False 2. The odd-numbered pounds on an upright scale are marked with numbers. * a. True b. False 3. The gatch handles to the bed should be left out at all times. * a. True b. False 4. You should tell the patient that you are counting her respirations. * a. True b. False 5. For good posture and even weight distribution, the patient’s feet...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT