Question

Determine the maximum shear stress (in MPa, using 2 decimal places) for a beam with the...

Determine the maximum shear stress (in MPa, using 2 decimal places) for a beam with the following data:

  1. Beam is 8 m in length (simply supported)
  2. Has an applied uniform distributed load of 39 kN/m
  3. Rectangular cross section rectangular with a base of 97 mm and a height of 235 mm
Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

I hope I could help u dear

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6...
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2 m from the left support. Assuming that the beam has a rectangular shape whose width and depth are 150 mm and 250 mm, respectively. Determine the maximum flexural stress in MPa developed in the beam.
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm...
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm x 25 mm flange and a 600 mm x 15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the 6 m span girder. Each weld has an allowable load of 330 kN/m. 1.Determine the maximum allowable shear force V for the girder in kN. 2. Calculate the maximum bending stress of the girder if...
True false: 1) When subjected to bending, a beam only develops normal stress in tension and...
True false: 1) When subjected to bending, a beam only develops normal stress in tension and compression 2)the shear flow is defined as an average force per unit length for each cross-section. 3)due to bending shear flow develops only along the beam length. 4)) shear center is defined as the point through which force can be applied without causing torsion Fill in the blank: the shear stress induced by bending in a beam is ............ Solve the question problem: A...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan. The...
Plot the shear force and bending moment digrams for an 8m long beam simply supported at...
Plot the shear force and bending moment digrams for an 8m long beam simply supported at 0m and 6m. There is a distributed load of 10 KN/m between the two supports and there is a point load of 20kN located at the end of the beam.
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.
For a bronze alloy, the stress at which plastic deformation begins is 284 MPa and the...
For a bronze alloy, the stress at which plastic deformation begins is 284 MPa and the modulus of elasticity is 123 GPa. (a) What is the maximum load that can be applied to a specimen having a cross-sectional area of 305 mm2 without plastic deformation? (b) If the original specimen length is 112 mm, what is the maximum length to which it may be stretched without causing plastic deformation? (a) N (b) mm
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian. (6 M Blease i want prompt clear solution for this question in detail,.
A simply supported reinforced-concrete beam has to resist a maximum factored moment of M* = 210...
A simply supported reinforced-concrete beam has to resist a maximum factored moment of M* = 210 KN-m. Given that f’c = 32 MPa, fy = 500 MPa and that the maximum possible width for the beam is 240 mm: a. Establish an appropriate structural depth ‘d’ for the beam b. Determine the total depth ‘D’ of the beam for a FRL of 90 minutes c. Find the area of steel Ast required to resist the moment and select the rebars....
For a bronze alloy, the stress at which plastic deformation begins is 270 MPa and the...
For a bronze alloy, the stress at which plastic deformation begins is 270 MPa and the modulus of elasticity is 125 GPa. (a) What is the maximum load that can be applied to a specimen having a cross-sectional area of 303 mm2 without plastic deformation? (b) If the original specimen length is 102 mm, what is the maximum length to which it may be stretched without causing plastic deformation
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT