Question

SAE 30 Oil at 60oF flows through a 1.5 m diameter pipe at a velocity of...

  1. SAE 30 Oil at 60oF flows through a 1.5 m diameter pipe at a velocity of 2.5 m/s.
    1. (3 points) What type of flow is occurring in the pipe:

            

  

  1. (2 points) If the pipe is made out of cast iron, determine the friction factor for flow through this pipe.
Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along...
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along 500 m length. Given: dynamic viscosity, μ and density, ρ of SAE 10 oil are 1.04 x 10-1 Ns/m2 and 917 kg/m3 respectively. By assuming the flow is laminar, determine energy head and pressure loss due to pipe friction using Hagen-Poiseuille equation and friction factor, f.
Water flows through a pipe of 5mm in diameter with a mean velocity of 0.2 m/s....
Water flows through a pipe of 5mm in diameter with a mean velocity of 0.2 m/s. The dynamic viscosity of the water is given as 10-3 Pa s. Establish whether the equation f = 64/Re may be used to calculate the friction factor for this flow.
Water flow horizontally for 4 m through a 65mm diameter cast iron pipe at an average...
Water flow horizontally for 4 m through a 65mm diameter cast iron pipe at an average velocity of 2 ms-1before an 90 degree elbow changes the direction of the flow downwards for a further 9 m. A ball valve is fitted at the end of the 9 m length of pipe. Determine the pressure at the pipe inlet if the ball valve is fully opend.(density of water = 998 kgm-3 , u=8.9*10^-4 Pas) I just calculated the friction losses before...
A pipe with diameter 30 cm carries oil of sp.gr. 0.95 at a velocity of 4...
A pipe with diameter 30 cm carries oil of sp.gr. 0.95 at a velocity of 4 m/s .at another section the diameter change to 20 cm . Find the velocity at this section and also find the mass flow rate of oil . my question kinematics of flow
Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity...
Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity of SG=0.88. (The rest of this is made up numbers and may not be indicative of actual car engine behavior) Assume that the oil flows at a velocity of V=2ft/s through a cast iron conduit within the engine block. Treat the conduit as a “best case roughness” (use smallest number for ε if needed) cast iron pipe with a diameter of 0.5in and a...
2. (25pts) Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a...
2. (25pts) Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity of SG=0.88. (The rest of this is made up numbers and may not be indicative of actual car engine behavior) Assume that the oil flows at a velocity of V=2ft/s through a cast iron conduit within the engine block. Treat the conduit as a “best case roughness” (use smallest number for ε if needed) cast iron pipe with a diameter of 0.5in...
Water flows through a 5-cm-diameter pipe at the average velocity of 1.25 m/s. (a) In the...
Water flows through a 5-cm-diameter pipe at the average velocity of 1.25 m/s. (a) In the dimensions of L/s, what is the volumetric flow rate? (b) If the diameter of the pipe is reduced by 20% at a constriction, by what percentage does the water’s velocity change? I need answer only in typed form. otherwise I'll downvote
Oil, with ?=860 kg/m3 and µ=0.06 kg/m ?s, flows through a horizontal pipe of 15 m...
Oil, with ?=860 kg/m3 and µ=0.06 kg/m ?s, flows through a horizontal pipe of 15 m length. The power delivered to the flow is 1 hp. If friction losses are to be neglected and the flow is at the laminar transition point (a) What is the appropriate pipe diameter? (b) For this condition, what are Q in m3/h; and (c) ?W in kPa?
The oil flows in a vertical pipe that has overall height of 30 m. The pressure...
The oil flows in a vertical pipe that has overall height of 30 m. The pressure at the inlet of the pipe (before the pump) and at the location of oil delivery at the end of the pipe are both atmospheric. Determine: 1- The head supplied to the flow by the pump. 2- The pressure at the exit of the pump. 2- The pressure at midway location of the pipe between    inlet and exit. Oil viscosity and density are...
3. Water flows through 80 ft of a 4” cast iron pipe. The head loss through...
3. Water flows through 80 ft of a 4” cast iron pipe. The head loss through the pipe is 0.27 ft. What is the volume flow rate of water through the pipe, in cfs? [Type II]
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT