Question

in the Flame test for sodium ions Procedure is : dip a cleaned flame test wire...

in the Flame test for sodium ions Procedure is : dip a cleaned flame test wire and clean in HCL into each urine specimen, then place the wire loop in a flame. then record the color of the flame... Question: How can you tell if the urine is normal or abnormal by the color of the flame of the sodium ion?

Homework Answers

Answer #1

In flame test, yellow colouration is produced by the presence of sodium ion in urine samples.
There is no proper standard to specify abnormal or normal urine sample by measuring the Sodium level in urine. However, very low and very high content of sodium is treated as abnormal urine sample.
Though flame test is a qualitative analysis technique, we can't quantitatively describe the amount of Sodium in urine sample by seeing the flame.
However, the most intense yellow flame is observed for the highest concentrated urine sample and low intensity is seen for the lowest concentration of sodium in urine sample.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Experiment 1: Observe the Reactions Between Halide and Calcium Ions Take four test tubes from the...
Experiment 1: Observe the Reactions Between Halide and Calcium Ions Take four test tubes from the Containers shelf and place them on the workbench. Fill each test tube with a different halide solution from the Materials shelf, as directed below. You may want to label the test tubes by double-clicking on each test tube and renaming it. Test Tube # Halide Solution 1 10.5 mL 0.1 M sodium chloride 2 10.5 mL 0.1 M sodium fluoride 3 10.5 mL 0.1...
Questions are after the procedures. Procedure 1) For Trial 1, use a graduated cylinder to measure...
Questions are after the procedures. Procedure 1) For Trial 1, use a graduated cylinder to measure 5 mL of 1 M sodium sulfate (Na2SO4). Place the sodium sulfate in a beaker. Using a clean graduated cylinder, add 5 mL of 1 M calcium chloride (CaCl2) to the beaker. Stir to mix well. 2) Using two Büchner funnels as in the diagram below, set up a funnel system with a safety flask to protect the water system from contaminants. 3) Filter...
I am having trouble creating a procedure to use to identify five unknown solutions we will...
I am having trouble creating a procedure to use to identify five unknown solutions we will be given in chem lab. The five solutions will be an acid, a base, a chloride salt, a nitrate salt, and a sodium salt. I have to come up with steps to determine which compound is in each category. Only one will be in each solution. Acid- HCl, HNO3, H2SO4 Base - NaOH, NH3, Na2S Chloride Salt - NaCl, BaCl2, CuCl Nitrate Salt -...
In experiment five, the "Identification of Ions in Salts", you will use a series of reactions...
In experiment five, the "Identification of Ions in Salts", you will use a series of reactions to identify a cation in one unknown and a cation-anion in another unknown. In this experiment primarily precipitation reactions or dissolving of precipitates will be used. The color and texture of the precipitate will be important to observe. In the identification of the anion the formation of a gas will be used to help ID the anion and a flame test will be used...
Procedure Experiment 1: Standardize an NaOH Solution Using Benzoic Acid as Primary Standard Part 1: Prepare...
Procedure Experiment 1: Standardize an NaOH Solution Using Benzoic Acid as Primary Standard Part 1: Prepare the NaOH Solution Take a 250 mL volumetric flask from the Containers shelf and a balance from the Instruments shelf and place them on the workbench. Zero the mass of the volumetric flask on the balance. Take sodium hydroxide from the Materials shelf and add 1 g to the flask. Record the mass from the balance display. Place the volumetric flask on the workbench....
Procedure Reaction 1: Dissolving the Copper 1. Obtain a clean, dry, glass centrifuge tube. 2. Place...
Procedure Reaction 1: Dissolving the Copper 1. Obtain a clean, dry, glass centrifuge tube. 2. Place a piece of copper wire in a weighing paper, determine the mass of the wire and place it in the centrifuge tube. The copper wire should weigh less than 0.0200 grams. 3. In a fume hood, add seven drops of concentrated nitric acid to the reaction tube so that the copper metal dissolves completely. Describe your observations in the lab report. (Caution, Concentrated nitric...
1. What is the resistance of a NichromeTM wire at 0.0 ∘C∘C if its resistance is...
1. What is the resistance of a NichromeTM wire at 0.0 ∘C∘C if its resistance is 106.9 ΩΩ at 12.5 ∘C∘C? The temperature coefficient of resistivity for NichromeTM is 4.00×10−4 (∘C)−1(∘C)−1 . Enter your answer with four significant figures. 2. A heart defibrillator is used to enable the heart to start beating if it has stopped. This is done by passing a large current of 12 AA through the body at 30 VV for a very short time, usually about...
Below is the background info for the lab assignment. The 4 blank boxes are the questions...
Below is the background info for the lab assignment. The 4 blank boxes are the questions I would like answers too. The end point for the fine titration was 35.90 mL in the burette when the solution turned bright green again. And the coarse titration I got 35.36mL as the end point. 35.9 mL is exact in case you need that info. Thanks! Background In this lab, we will determine the amount of alcohol (ethanol), C2H5OH, in a commercial vodka...
Meningitis Case Study Jason Hinojosa is a 5-week-old infant brought to the emergency department by his...
Meningitis Case Study Jason Hinojosa is a 5-week-old infant brought to the emergency department by his mother, who speaks little English. Her husband is at work. Mrs. Hinojosa is young, anxious, and appears frightened. Through a translator, Mrs. H. reports that her son has not been eating, sleeps all the time, and “is not normal.” 1. What are some of the obstacles you will need to consider, recognizing that Mrs. H. does not speak or understand English well? 2. You...
Sodium Borohydride Reduction Reaction 1. Dissolve 600 mg of your carbonyl compound in 3 mL of...
Sodium Borohydride Reduction Reaction 1. Dissolve 600 mg of your carbonyl compound in 3 mL of methanol. Cover the flask with aluminum foil when not adding reagents or taking TLC samples to keep any water from getting in. 2. Cool your flask to 0° C using ice/water. 3. Allow to stir in the ice for 2 minutes then slowly add 0.4g of NaBH4 to your solution, then remove from ice bath and stir at room temperature. 4. After 10 min,...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT