Question

If the concentration of NaOH used in today's lab was not standardized properly, and is actually...

If the concentration of NaOH used in today's lab was not standardized properly, and is actually higher. How would this error change your calculated Ka value? (Increase it, Decrease it, Unaffected) Briefly Explain

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
If the concentration of NaOH used in today's lab was not standardized properly, and is actually...
If the concentration of NaOH used in today's lab was not standardized properly, and is actually higher. How would this error change your calculated Ka value? (Increase it, Decrease it, Unaffected) Briefly Explain
The NaOH used in this lab should have been 0.1M, since you were to make it...
The NaOH used in this lab should have been 0.1M, since you were to make it as such (see Step 15 in lab document). Compare your standardized average molarity of NaOH in this lab to 0.1M. How do the values compare? How close was your NaOH dilution to actually being 0.1M NaOH? Calculate your percent error against the average standardized value from this lab. (You must show all work to receive credit.) step 15- Prepare an aliquot (fancy chemical term...
See experiment info below The NaOH used in this lab should have been 0.1M, since you...
See experiment info below The NaOH used in this lab should have been 0.1M, since you were to make it as such (see Step 15 in lab document). Compare your standardized average molarity of NaOH in this lab to 0.1M. How do the values compare? How close was your NaOH dilution to actually being 0.1M NaOH? Calculate your percent error against the average standardized value from this lab. (You must show all work to receive credit.) step 15- Prepare an...
A single effect evaporator is used to increase the concentration of a 44% NaOH solution to...
A single effect evaporator is used to increase the concentration of a 44% NaOH solution to 65%. The initial flow rate of the feed solution (40°C) is 50,000 kg/h. Steam at 3 atm is used to heat the system. The temperature in the vapor space is 40°C and the overall heat transfer coefficient is estimated as 2,000 W/m2 ·°C. Calculate the amount of steam consumed and surface area needed for heating. can you show how you calculated the latent heat...
What volume of 0.5 M NaOH is needed to perform the titration of 30 mL of...
What volume of 0.5 M NaOH is needed to perform the titration of 30 mL of 0.1 M H3PO4? Question options: a) V = 12 mL b) V = 6 mL c) V = 18 mL d) V = 30 mL he pH at the equivalence point when a 0.20 M weak base (Ka = 9.1 x 10-7) is titrated with a 0.20 M strong acid is: Question options: a) pH = 2.9 b) pH = 1.7 c) pH =...
An approximately 0.1 M NaOH solution is prepared by adding 2.0 g of solid NaOH to...
An approximately 0.1 M NaOH solution is prepared by adding 2.0 g of solid NaOH to 500 mL of water. The precise concentration of the solution is determined by titrating the NaOH against weighed portions of a weak acid, pot assium hydrogen phthalate (KHP), obtained from the National Institute of Standards and Technology (NIST) and certified as being 99.99% pure. The KHP samples are weighed by difference on an analytical balance. Following its standardization, the NaOH solut ion is used...
Molarity of NaOH and molecular weight of the unknown acid Part A Run 1 Run 2...
Molarity of NaOH and molecular weight of the unknown acid Part A Run 1 Run 2 Mass of H2C2O4*2H20 used in grams 0.2127 0.2124 Moles of H2C2O4*2H2O (mol) 1.69 *10^-5 1.69*10^-5 Number of protons available for reaction with OH- 2H 2H Moles of OH- which reacted (mol) 2 2 Volume of NaOH solution used (mL) 18.71 19.15 Molarity of NaOH soultion (M) .12 .12 Average molarity of NaOH (M) Part B with unkown sample Run 1 Run2 Mass of unknown...
How would the calculated molarity for NaOH be affected (higher, lower, or no change) if the...
How would the calculated molarity for NaOH be affected (higher, lower, or no change) if the following procedural errors occurred? Explain why in each case. a. While pipetting the H2SO4 solution, several drops of H2SO4 drip out of your pipet onto the bench top and miss the Erlenmeyer flask. NaOH molarity (circle one): high or low Why? b. The buret tip is not filled with NaOH at the beginning of the titration. NaOH molarity (circle one) : high or low...
What would be the effect (increase, decrease, no change) on the calculated value of R for...
What would be the effect (increase, decrease, no change) on the calculated value of R for the following procedural error. Explain why. You forgot to account for the water vapor pressure and used the barometric pressure as th pressure of the hydrogen gas.
A. The manufacturer of the vinegar used in the experiment stated that the vinegar contained 5.0%...
A. The manufacturer of the vinegar used in the experiment stated that the vinegar contained 5.0% acetic acid. What is the percent error between your result and the manufacturer’s statement? B. What challenges would you encounter with the titration if you had used apple cider vinegar or balsamic vinegar as the analyte instead of white vinegar? The issue with using a dark color vinegar is the coloring in the end. C. How would your results have differed if the tip...