Question

I need name of final compund and step by step equaions for the following experiment: Ethylenediamine...

I need name of final compund and step by step equaions for the following experiment: Ethylenediamine complexes of Nickel Procedure 1. Dissolve 1.3g NiCl2 6H2O in 1.5 mL of warm water. 2. With stirring, slowly add 5mL of 50% ethylenediamine solution 3. Cool in ice for 15 min., add 10mL ethanol(95%) and put back in the ice bath for 10min. 4.Filter, and then wash with two 10mL portions of ethanol and two 10mL portions of ether. 5. Air dry, weigh, bottle, and label the blue-purple product.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
I have posted the procedure of the lab below. Please tell me what the theoretical yield...
I have posted the procedure of the lab below. Please tell me what the theoretical yield is for aspirin based on this procedure and explain how you got it. I am not sure I am doing this right. SYNTHESIS OF ASPIRIN Procedure: Start heating a water bath in your 250 mL beaker by filling it with ~150 mL of tap water. Carefully weigh out 1.0 gram of salicylic acid. Transfer to a 50 mL Erlenmeyer flask. In the fume hood,...
1. a) draw the structure of the product you would have isolated if you had used...
1. a) draw the structure of the product you would have isolated if you had used NaBD4 in D2O in this experiment, write a mechanism explaining the result. (b) give the product structure for the same reaction using NaBD4 in H2O. Assume that there is no hydrogen exchange between NaBD4 and the solvent. Not sure if this is relevant to the question but here is the procedure used: Dissolve 3.8g of vanillin in 12mL of ethanol in a small beaker...
Sodium Borohydride Reduction Reaction 1. Dissolve 600 mg of your carbonyl compound in 3 mL of...
Sodium Borohydride Reduction Reaction 1. Dissolve 600 mg of your carbonyl compound in 3 mL of methanol. Cover the flask with aluminum foil when not adding reagents or taking TLC samples to keep any water from getting in. 2. Cool your flask to 0° C using ice/water. 3. Allow to stir in the ice for 2 minutes then slowly add 0.4g of NaBH4 to your solution, then remove from ice bath and stir at room temperature. 4. After 10 min,...
Synthesis of Bromonitrosylbis(triphenylphosphine)nickel(O), NiBr(NO)(PPh3)2 Put a wide-based pyrex dish on a stirrer-hotplate, and put a medium-large...
Synthesis of Bromonitrosylbis(triphenylphosphine)nickel(O), NiBr(NO)(PPh3)2 Put a wide-based pyrex dish on a stirrer-hotplate, and put a medium-large stirrer bar in the dish. (If appropriate pyrex dishes are not available, use a metal water bath.) Set up a 100 cm3 round-bottom flask with a reflux condenser in the dish, leaving enough room below the bottom of the flask for the stirrer bar in the dish. Fill the pyrex dish with water so that the water come about ½ way up the round-bottom...
Calculate the percentage Yield of the preparation of Tris(thiourea)copper(I)chloridePreparation of Tris(Thiourea) Copper (I) Chloride Dissolve 5.0g...
Calculate the percentage Yield of the preparation of Tris(thiourea)copper(I)chloridePreparation of Tris(Thiourea) Copper (I) Chloride Dissolve 5.0g of Thiourea in 25 mL of hot Water, add 1.0g of Copper Turnings. In a fume hood, add 5 mL of concentrated HCl to this mixture. Heat this on a Steam bath while the Copper dissolves. Do not boil. Add Water if needed to maintain the liquid at a constant level. Filter the hot solution and allow to cool slowly. White opaque crystals will...
Describe the role of the melting point depression phenomenon in this Solventless Aldol Experiment. the Eperiment:...
Describe the role of the melting point depression phenomenon in this Solventless Aldol Experiment. the Eperiment: Experimental Procedure: 1. in test tube, mix two solid reactants with spatula until an oil forms (melting point depression): In a small test tube, mix 0.25 g 3,4-dimethoxybenzaldehyde and 0.20 g 1-indanone. Crush the solids completely, using a glass rod or metal spatula. Caution: Avoid pressing hard on the bottom of the test tube. Continue stirring until a yellowish oil forms. 2. Add 50...
I have provided the information for the lab below. I want to see the chemical reactions...
I have provided the information for the lab below. I want to see the chemical reactions that take place during each step of the experiment. So in the procedures when a chemical was added i would like to see what the products and byproducts that were formed. I also want to see one over all reaction for this experiment to just get an overview of what exactly is happening during the experiment. Thank you:) Part B: Synthesis of [Co(NH3)5Cl]Cl2 Objective:...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT