Question

If some of the KHP was spilled on the balance pan while weighing, how will the...

If some of the KHP was spilled on the balance pan while weighing, how will the calculated molarity of the NaOH be affected (too low, too high, unaffected)? Explain.

Homework Answers

Answer #1

answer : too low

explanation:

when KHP was present on balance pan while weighing the NaOH it will effect the concentration of NaOH. KHP will react with NaOH forms salt from the following eqaution.

KHP + NaOH ----------------------> NaKP + H2O

so some moles of NaOH already react with KHP . the mass measured is not actual mass of NaOH . it is the mass of NaOH and salt formed from KHP. so the total mass is more than that of NaOH measured mass . apparently the mass of NaOH decreases . so moles decreases . if moles decreases moalrity also decreases

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The water for the pan (Part A.3) is not saturated with Co2. Will the reported percent...
The water for the pan (Part A.3) is not saturated with Co2. Will the reported percent CaCO3 in the original sample be too high, too low, or unaffected? Explain.
How would the calculated molarity for NaOH be affected (higher, lower, or no change) if the...
How would the calculated molarity for NaOH be affected (higher, lower, or no change) if the following procedural errors occurred? Explain why in each case. a. While pipetting the H2SO4 solution, several drops of H2SO4 drip out of your pipet onto the bench top and miss the Erlenmeyer flask. NaOH molarity (circle one): high or low Why? b. The buret tip is not filled with NaOH at the beginning of the titration. NaOH molarity (circle one) : high or low...
If the KHP was not kept dry prior to its use for this experiment, how would...
If the KHP was not kept dry prior to its use for this experiment, how would moisture affect the calculated concentration of the NaOH solution? If it takes 16.39 mL of an unknown concentration aqueous solution of NaOH to neutralize 1 g of pure benzoic acid (C7H6O2), then what is the molarity of the NaOH solution?
For each of the following determine whether the calculated molarity would be too low, too high,...
For each of the following determine whether the calculated molarity would be too low, too high, or unaffected and explain why? a. You added 1.0 zinc (instead of 0.3-0.4g) to your unknown. b. You added 50 ml DI (instead of 25mL) to your 10.00 mL unknown sample and then added the Zn c. the cooper was not completely dry before weighing
Will the calculated molarity of the NaOH solution be too high or too low if a...
Will the calculated molarity of the NaOH solution be too high or too low if a student "overshoots" the end point of the titration? Explain.
An approximately 0.1 M NaOH solution is prepared by adding 2.0 g of solid NaOH to...
An approximately 0.1 M NaOH solution is prepared by adding 2.0 g of solid NaOH to 500 mL of water. The precise concentration of the solution is determined by titrating the NaOH against weighed portions of a weak acid, pot assium hydrogen phthalate (KHP), obtained from the National Institute of Standards and Technology (NIST) and certified as being 99.99% pure. The KHP samples are weighed by difference on an analytical balance. Following its standardization, the NaOH solut ion is used...
The accuracy of this experiment depends on good technique. Would the following techinque errors result in...
The accuracy of this experiment depends on good technique. Would the following techinque errors result in an erroneously high or an erroneously low calculated molarity of an NaOH solution? Breifly explain your reasoning for each answer. a) The KHP you used had not been dried. b) When filling the buret with NaOH you left a air bubble in the buret tip.The bubble was released during your first KHP titration. c) After completeing the titration you noticed droplets of titrant clinging...
Question : The accuracy of this experiment depends on good technique. Would the following techinque errors...
Question : The accuracy of this experiment depends on good technique. Would the following techinque errors result in an erroneously high or an erroneously low calculated molarity of an NaOH solution? Breifly explain your reasoning for each answer. a) The KHP you used had not been dried. b) When filling the buret with NaOH you left a air bubble in the buret tip.The bubble was released during your first KHP titration. c) After completeing the titration you noticed droplets of...
How would the molar mass of the unknown be affected (increase, decrease, no change) if the...
How would the molar mass of the unknown be affected (increase, decrease, no change) if the following occurred during the lab? Explain. a. Some unknown solids were spilled while transferring into the beaker. b. The buret was rinsed with DI H2O but not conditioned with the 0.20 M NaOH solution.
The use of good technique while doing this experiment is very important. Briefly explain how the...
The use of good technique while doing this experiment is very important. Briefly explain how the following technique errors would affect the determination of the molar concentration of acetic acid in vinegar 1. A student stops the titration when the pink persists through the solution for less than 10 s. Explain your reasoning. A. When the titration is stopped before the real endpoint has been reached, the calculated volume of sodium hydroxide needed for the titration will be too low....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT