Question

An IV is infusing at 80 ml/h potassium chloride 20mEq was added to 1000 mL of...

An IV is infusing at 80 ml/h potassium chloride 20mEq was added to 1000 mL of IV solution. How much potassium chloride is administered per hour in mEq/h?

Homework Answers

Answer #1

From the given data,

IV infusing KCl at the rate = 80 ml/h

concentration of KCl = 20 mEq

volume to which KCl added = 1000 ml IV solution,

So,

KCl administered per hour = 20 mEq x 80 ml/h x 1/1000 ml

                                           = 1.6 mEq/h

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Is there enough medication in a 60 mL package of Potassium Chloride Oral Solution 10%, 20...
Is there enough medication in a 60 mL package of Potassium Chloride Oral Solution 10%, 20 mEq per 15 mL, to fulfill an order of 80 mL? Yes  or   No . If so explain.
Silver sulfate solution is added to 25.00 mL of a 0.500 M potassium chloride solution until...
Silver sulfate solution is added to 25.00 mL of a 0.500 M potassium chloride solution until no precipitate forms. If 45 mL of silver sulfate were added to react completely with the potassium chloride, what was the original concentration of silver sulfate solution? What concentration of sulfate will remain in solution after the reaction is complete if 45 mL of silver sulfate solution were added to the potassium chloride solution?
The IV pump is infusing at 25 gtt/min. There are 600 mL to be infused and...
The IV pump is infusing at 25 gtt/min. There are 600 mL to be infused and the set calibration is 10 gtt/mL. How many hours will the IV fluid run? 4 hours 5 hours 6 hours 8 hours
Mrs. Kelly is to have 1000 mL of I.V. solution with KCL 30 mEq added. The...
Mrs. Kelly is to have 1000 mL of I.V. solution with KCL 30 mEq added. The order states that the I.V. should infuse over the next 5 hours. The dose on hand is 40 mEq/10 mL. The drop factor is 60 gtt/mL. a. How many mL of KCL will you add to the 1000 mL bag? b. What will the flow rate be in mL/hr? c. What will the flow rate be in gtt/min?
You have 375 mL of a 1.25 M potassium chloride solution, but you need to make...
You have 375 mL of a 1.25 M potassium chloride solution, but you need to make a 0.50 M potassium chloride solution. How many milliliters of water must you add to the original 1.25 M solution to make the 0.50 M potassium chloride solution? Note: Assume the volumes are additive. Anwer should be in mL of water.
An Iv infusing at 30 drops/min. The DF is 20. How many mL/hr are being infused...
An Iv infusing at 30 drops/min. The DF is 20. How many mL/hr are being infused at this rate?
A patient is admitted and an IV of 1000 mL D5RL is started. Later an IV...
A patient is admitted and an IV of 1000 mL D5RL is started. Later an IV antibiotic is ordered for the patient. This is sent from the pharmacy already prepared in a small-volume IV solution bag. The setup used to infuse this medication is referred to as a. centeral line b. a primary line c. iv Piggyback d.peripheral line? How is this abbreviated?
The IV ordered is 1000 mL D-10-W IV q12h. The drop factor is 10 gtts/mL. a....
The IV ordered is 1000 mL D-10-W IV q12h. The drop factor is 10 gtts/mL. a. Calculate the flow rate in mL/h. b. Calculate the flow rate in gtts/min.
55.2 mL of 0.976 M perchloric acid is added to 45.9 mL of potassium hydroxide, and...
55.2 mL of 0.976 M perchloric acid is added to 45.9 mL of potassium hydroxide, and the resulting solution is found to be acidic. 18.5 mL of 2.08 M sodium hydroxide is required to reach neutrality. What is the molarity of the original potassium hydroxide solution?
How many grams of potassium chlorate decompose to form potassium chloride and 650. mL O2 at...
How many grams of potassium chlorate decompose to form potassium chloride and 650. mL O2 at 128°C and 663 torr?