Question

You take three 20.0mL samples of KHP and find the average moles per mL to be...

You take three 20.0mL samples of KHP and find the average moles per mL to be 0.00206. What would the total moles of KHP be if the intial volume was 100.0 mL?

Homework Answers

Answer #1

Do you mean each of the three 20 ml samples taken for analysis is from the same (100 ml) stock solution of KHP. This question is answered on that basis.

Average moles of KHP per ml of the solution = 0.00206

This means that 1 ml of the solution contains 0.00206 moles

Initial volume of the solution = 100 ml

Total moles of KHP in 100 ml of the solution = 100 ml x 0.00206 moles/ml = 0.206 moles.

Note; Even if 20 ml is taken for analysis , concentration is reported as moles per ml. Hence no need to consider 20 ml in calculation

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Part IV. Based on the average number of moles of IO3- in your samples, and the...
Part IV. Based on the average number of moles of IO3- in your samples, and the initial volume of those samples, what is the solubility of Ca(IO3)2 in mol/L of the saturated solution in pure water? You should report 3 significant figures, e.g. 0.00603. Avg. Moles :0.000108 moles Initial Vol: 6.52 mL
1b. Calculate the exact molarity of a solution of NaOH if 55.00 mL of it is...
1b. Calculate the exact molarity of a solution of NaOH if 55.00 mL of it is needed to titrate an amount of KHP that equals your average mass (that you stated above). Average is 50.0 (4 pts) 2a. What is the average molarity for your standardized NaOH solution?_______________ (1 pt) Average: .0075 M 2b. If 1.20 grams of impure solid KHP sample required 2.53 mL of your standardized NaOH to reach the end point, what was the percent KHP in...
a) What volume of a 6.40  M stock solution do you need to prepare 500.  mL of a...
a) What volume of a 6.40  M stock solution do you need to prepare 500.  mL of a 0.0347  M solution of HNO3? b) The absorbance of a cationic iron(II) sample solution was measured in a spectrophotometer, but the instrument returned an error because the absorbance was too high. The sample was then diluted by using a pipette to take 100.0 μL of the sample and injecting it into a cuvette already containing 2.00 mL of water (total volume is 2.00 mL +...
Previous question: To 100 mL of pure H2O, you add 0.01 moles of the weak acid...
Previous question: To 100 mL of pure H2O, you add 0.01 moles of the weak acid KHP (potassium hydrogen phthalate). Assuming the system behaves ideally (activity coefficients are all equal to 1), calculate and report the pH of the resulting solution. ANSWER: pH=3.2 Still considering the KHP system from the previous question, let’s now consider the non-ideal system in which the activity coefficients are γKHP = 0.95, γKP -= 1.2, γH3O+ = 0.95. In terms of absolute concentrations, what is...
A.) A student removed 125.0 mL of a 0.155 M KCl solution? How many moles of...
A.) A student removed 125.0 mL of a 0.155 M KCl solution? How many moles of KCl are in this sample? B.) A student needed 0.761 mol of HCl. What volume (in L) of 0.131 M HCl solution would she take in order to get this sample?
A 100.0 mL flask is filled with 0.065 moles of A and allowed to react to...
A 100.0 mL flask is filled with 0.065 moles of A and allowed to react to form B according to the reaction below. The following experimental data are obtained for the amount of A as the reaction proceeds. What is the average rate of appearance of B in units of M/s between t = 10 min. and t = 30 min.? Assume that the volume of the flask is constant. A(g) → B(g) Time 0.0 10.0 20.0 30.0 40.0 Moles...
1. "After cleaning and filling your buret, you take an initial reading of the volume and...
1. "After cleaning and filling your buret, you take an initial reading of the volume and determine it to be 0.25 mL. You add some of the solution to a beaker, and take a final reading of the buret at 29.50 mL. What volume of solution did you add to the beaker?" 2.Magenisum carbonate (MgCO3) is a common active ingredient in antacids. Each mole of magnesium carbonate can neutralize two moles of acid. If one tablet neutralized 0.0122 moles of...
1. Assuming a negligible change in volume, how many moles of H3O+ or OH– must you...
1. Assuming a negligible change in volume, how many moles of H3O+ or OH– must you add per litre to an acidic solution to adjust its pH from 5.80 to 6.25? (A) 1.58 x 10–6 mol H3O+ (B) 2.14 x 10–6 mol OH– (C) 1.02 x 10–6 mol H3O+ (D) 1.02 x 10–6 mol OH– (E) 2.14 x 10–4 mol H3O+ 2.. A buffer is prepared by mixing 100.0 mL of a 0.100 mol L–1 CH3COOH solution with a 0.200...
2. What is the temperature in Kelvin for 0.112 moles of an ideal gas at 0.888...
2. What is the temperature in Kelvin for 0.112 moles of an ideal gas at 0.888 atm in a container that has a volume of 675 mL? (Your answer should have three significant figures). 3.What is the total pressure in atm for a 1807 mL container at 28.05º C that contains 5.00 grams each of CO2, H2O, and N2? (The answer should have three sig figs.) 4. A Noble Gas has a density of 2.3013 g/L at 1185.6 torr and...
Citric acid has three pKa's: 3.13, 4.76 and 6.39. If you add sufficient solid NaOH to...
Citric acid has three pKa's: 3.13, 4.76 and 6.39. If you add sufficient solid NaOH to 100.0 mL of 0.5 M citric acid to bring the pH to 4.00 (assume all the NaOH dissolves without altering the total volume), what are the concentrations of the major species present in the solution? How many additional miles of NaOH would you need to add to bring the solution to a pH or 5? Which species are present in the solution at that...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT