Question

Draw and label a box diagram of a spectrophotometer that could use for a UV/Vis absorption...

Draw and label a box diagram of a spectrophotometer that could use for a UV/Vis absorption experiemt

Homework Answers

Answer #1

A diagram of the components of a typical spectrometer are shown in the following diagram. The functioning of this instrument is relatively straightforward. A beam of light from a visible and/or UV light source (colored red) is separated into its component wavelengths by a prism or diffraction grating. Each monochromatic (single wavelength) beam in turn is split into two equal intensity beams by a half-mirrored device. One beam, the sample beam (colored magenta), passes through a small transparent container (cuvette) containing a solution of the compound being studied in a transparent solvent. The other beam, the reference (colored blue), passes through an identical cuvette containing only the solvent. The intensities of these light beams are then measured by electronic detectors and compared. The intensity of the reference beam, which should have suffered little or no light absorption, is defined as I0. The intensity of the sample beam is defined as I. Over a short period of time, the spectrometer automatically scans all the component wavelengths in the manner described. The ultraviolet (UV) region scanned is normally from 200 to 400 nm, and the visible portion is from 400 to 800 nm.

If the sample compound does not absorb light of of a given wavelength, I = I0. However, if the sample compound absorbs light then I is less than I0, and this difference may be plotted on a graph versus wavelength, as shown on the right. Absorption may be presented as transmittance (T = I/I0) or absorbance (A= log I0/I). If no absorption has occurred, T = 1.0 and A= 0. Most spectrometers display absorbance on the vertical axis, and the commonly observed range is from 0 (100% transmittance) to 2 (1% transmittance). The wavelength of maximum absorbance is a characteristic value, designated as ?max.
Different compounds may have very different absorption maxima and absorbances. Intensely absorbing compounds must be examined in dilute solution, so that significant light energy is received by the detector, and this requires the use of completely transparent (non-absorbing) solvents. The most commonly used solvents are water, ethanol, hexane and cyclohexane. Solvents having double or triple bonds, or heavy atoms (e.g. S, Br & I) are generally avoided. Because the absorbance of a sample will be proportional to its molar concentration in the sample cuvette, a corrected absorption value known as the molar absorptivity is used when comparing the spectra of different compounds. This is defined as:

Molar Absorptivity,? = A/ c l

( where A= absorbance, c = sample concentration in moles/liter
& l = length of light path through the cuvette in cm.)

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
What are the advantages of having a computer solely dedicated to a UV-Vis Spectrophotometer
What are the advantages of having a computer solely dedicated to a UV-Vis Spectrophotometer
In cohesive sentences, explain how photodiode array (PDA)-based single beam UV-Vis spectrophotometer works (illustrate your explanation...
In cohesive sentences, explain how photodiode array (PDA)-based single beam UV-Vis spectrophotometer works (illustrate your explanation by drawing a schematic diagram of a PDA-based spectrophotometer) What is the main advantage of the PDA based (reverse opticts) single beam instruments compared to the conventioal single beam ones?
a) Draw the structure of any compound that that could NOT be visualized with the UV...
a) Draw the structure of any compound that that could NOT be visualized with the UV lamp in C20, but would show a positive diiodine (I2) visualization. b) Draw the structure of any compound that could be visualized with the UV lamps in C20, but would NOT show a positive diiodine (I2) visualization.
Draw and label the diagram of the macroeconomy in Australia
Draw and label the diagram of the macroeconomy in Australia
A UV/vis light absorbance spectrophotometer produced the following linear calibration equation for a given standard, A=0.653C+0.0342...
A UV/vis light absorbance spectrophotometer produced the following linear calibration equation for a given standard, A=0.653C+0.0342 where C is the molar concentration and A is the absorbance. The detector's lifetime was running out, so the lab manager replaced the detector. Before the lab manager properly aligned the detector and diffraction grating, a student measured different standard concentrations and got the data in the second column of the table. The lab manager aligned the detector and diffraction grating and alerted the...
This question refers to a negative externality (a) Draw and label a diagram to illustrate a...
This question refers to a negative externality (a) Draw and label a diagram to illustrate a negative externality (b) Using your diagram explain the difference between the market and efficient allocations (c) Redraw your diagram and use it to explain why a Pigouvian tax can lead to an efficient allocation. What are the problems with a Pigouvian tax? (d) Draw your diagram a third time and use it to explain Coase Theorem. What are the problems with Coase theorem as...
Draw and label a diagram of the kidney and the major inlets and outlets to the...
Draw and label a diagram of the kidney and the major inlets and outlets to the kidney. What are the fluid flow rates in these major inlet and outlet streams?
1) Draw the valence bond model for H2O and label all the orbitals on the diagram....
1) Draw the valence bond model for H2O and label all the orbitals on the diagram. Describe the bonds and lone pairs by filling in this sentence. The H-O bonds are ___ bonds formed by the ____ overlap between the Hydrogen's _____ orbitals and the oxygen's _________ orbitals. The lone pairs reside on oxygen's _____ orbitals. 2) Draw the valence bond model for BrF5-1 and label all the orbitals on the diagram. Describe the bonds and lone pairs on all...
Draw or diagram, include nd label with function all features associated with the segment of DNA...
Draw or diagram, include nd label with function all features associated with the segment of DNA Agrobacterium tumefaciens transformed into an Arabidopsis chromosome from your recombinant pBlee. Diagram/ label/ function, only and all of the DNA inserte into the plant chromosome.
Enzyme Questions Draw a labelled energy-level diagram for an endergonic reaction. Label the products, reactants, transition...
Enzyme Questions Draw a labelled energy-level diagram for an endergonic reaction. Label the products, reactants, transition state, activation energy and, on the same diagram, draw the catalyzed reaction as well.