Question

A lathe to make a single pass on a 2.000 in. diameter (diameter before the cut),...

A lathe to make a single pass on a 2.000 in. diameter (diameter before the cut), 24 in. long part. The depth of cut is set to 0.125 in. at a spindle speed of 400 rev./min. with a feed of 0.012 in./rev.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A conical surface will open on an automatic lathe. The workpiece is 1000 mm long and...
A conical surface will open on an automatic lathe. The workpiece is 1000 mm long and the minimum and maximum diameter at opposite ends is 150 mm and 250 mm. Automatic controls on the lathe set the rotation speed as a function of the workpiece diameter, allowing the surface speed to be kept at a constant value of 200 m / min. Feed 0.5 mm / revolution and cutting depth 4.0 mm. The rough geometry of the part has been...
It is desired to drill a 350 mm diameter hole to a certain depth in a...
It is desired to drill a 350 mm diameter hole to a certain depth in a workpiece with a diameter of 500 mm and a diameter of 1000 mm by deep drilling. It takes 4.5 minutes to perform the drilling process by spraying high pressure liquid into the drilling point. Current spindle speed = 4000 rpm and feed = 0.004 cm / rev. In order to increase the surface quality in the hole, it was decided to reduce the feed...
The top surface of a rectangular workpart is machined using a peripheral milling operation. The workpart...
The top surface of a rectangular workpart is machined using a peripheral milling operation. The workpart is 735 mm long by 50 mm wide by 95 mm thick. The milling cutter, which is 60 mm in diameter and has five teeth, overhangs the width of the part equally on both sides. Cutting speed = 80 m/min, chip load = 0.30 mm/tooth, and depth of cut = 7.5 mm. (a) Determine the time required to make one pass across the surface,...
I did already posted this question before, I did get the answer but i am not...
I did already posted this question before, I did get the answer but i am not satisfied with the answer i did the code as a solution not the description as my solution, so i am reposting this question again. Please send me the code as my solution not the description In this project, build a simple Unix shell. The shell is the heart of the command-line interface, and thus is central to the Unix/C programming environment. Mastering use of...
The Boeing Company, headquartered in Chicago, Illinois, is one of the two major producers of aircraft...
The Boeing Company, headquartered in Chicago, Illinois, is one of the two major producers of aircraft in the global market. The other major producer is European Airbus. Boeing produces three models in Everett, Washington: 747s, 767s, and 777s. The planes are all produced in the same building. At any one time, there may be as many as six planes in various stages of production. Obviously the building has to be fairly large to accommodate such a huge undertaking. In fact,...
Write a Python 3 program called “parse.py” using the template for a Python program that we...
Write a Python 3 program called “parse.py” using the template for a Python program that we covered in this module. Note: Use this mod7.txt input file. Name your output file “output.txt”. Build your program using a main function and at least one other function. Give your input and output file names as command line arguments. Your program will read the input file, and will output the following information to the output file as well as printing it to the screen:...
Please read the article and answear about questions. Determining the Value of the Business After you...
Please read the article and answear about questions. Determining the Value of the Business After you have completed a thorough and exacting investigation, you need to analyze all the infor- mation you have gathered. This is the time to consult with your business, financial, and legal advis- ers to arrive at an estimate of the value of the business. Outside advisers are impartial and are more likely to see the bad things about the business than are you. You should...
Please answer the following Case analysis questions 1-How is New Balance performing compared to its primary...
Please answer the following Case analysis questions 1-How is New Balance performing compared to its primary rivals? How will the acquisition of Reebok by Adidas impact the structure of the athletic shoe industry? Is this likely to be favorable or unfavorable for New Balance? 2- What issues does New Balance management need to address? 3-What recommendations would you make to New Balance Management? What does New Balance need to do to continue to be successful? Should management continue to invest...
What tools could AA leaders have used to increase their awareness of internal and external issues?...
What tools could AA leaders have used to increase their awareness of internal and external issues? ???ALASKA AIRLINES: NAVIGATING CHANGE In the autumn of 2007, Alaska Airlines executives adjourned at the end of a long and stressful day in the midst of a multi-day strategic planning session. Most headed outside to relax, unwind and enjoy a bonfire on the shore of Semiahmoo Spit, outside the meeting venue in Blaine, a seaport town in northwest Washington state. Meanwhile, several members of...
Sign In INNOVATION Deep Change: How Operational Innovation Can Transform Your Company by Michael Hammer From...
Sign In INNOVATION Deep Change: How Operational Innovation Can Transform Your Company by Michael Hammer From the April 2004 Issue Save Share 8.95 In 1991, Progressive Insurance, an automobile insurer based in Mayfield Village, Ohio, had approximately $1.3 billion in sales. By 2002, that figure had grown to $9.5 billion. What fashionable strategies did Progressive employ to achieve sevenfold growth in just over a decade? Was it positioned in a high-growth industry? Hardly. Auto insurance is a mature, 100-year-old industry...