Question

i.      The maximum velocity of the piston and the maximum force that can be applied in the...

i.      The maximum velocity of the piston and the maximum force that can be applied in the forward stroke.       (2 points)

ii.      The maximum velocity of the piston and the maximum force that can be applied in the reverse stroke.         (2 points)

Hints:

Velocity:           V = Q/A

    V = Velocity of Piston

    A = Area of cylinder cross section,

    Q = volumetric flow rate,

Applied Force, F = p A

    F = Applied force

    p = fluid pressure

    A = Area of cylinder cross section, m2 (in2)

Homework Answers

Answer #1

Answer:-

Assume data

The inside diameter of the cylinder is 3.75 in. The piston rod has a diameter of 0.75 in.

The hydraulic power is 600 lb/in2 .

pressure at a flow rate of 1500 in3/min to drive the piston..

1) Velocity of piston ,  

Maximum force

2) Velocity of piston

Maximum force,

Please like it , if you have any issue mention in comment

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Determine the following: i.      The maximum velocity of the piston and the maximum force that can be...
Determine the following: i.      The maximum velocity of the piston and the maximum force that can be applied in the forward stroke.       (2 points) ii.      The maximum velocity of the piston and the maximum force that can be applied in the reverse stroke.         (2 points) Hints: Velocity:           V = Q/A     V = Velocity of Piston     A = Area of cylinder cross section,     Q = volumetric flow rate, Applied Force, F = p A     F = Applied force     p = fluid pressure     A = Area of...
A linear actuator such as you used in lab has a rod of area of 10-4...
A linear actuator such as you used in lab has a rod of area of 10-4 m2 and a piston area of 3*10-4 m2 . The actuator can have fluid applied to either the piston end of the cylinder or the open end where the rod comes out so the rod can both extend and retract out of the cylinder. A student establishes equilibrium between the hydraulic force and an external weight so there is no movement of the weight....
A piston-cylinder apparatus contains 4 kg of saturated liquid water at 35˚C. The piston’s cross sectional...
A piston-cylinder apparatus contains 4 kg of saturated liquid water at 35˚C. The piston’s cross sectional area is 0.06 m2 , and initially it is resting on stops, enclosing a volume of 0.03 m3 . To raise the piston, a pressure of 300kPa has to be applied. Heat is transferred until the volume is 0.075 m3 , at which point the piston encounters a linear spring. To deflect the spring 1 m, a force of 360 kN is required. More...
When gas expands in a cylinder with radius r, the pressure P at any given time...
When gas expands in a cylinder with radius r, the pressure P at any given time is a function of the volume V: P = P(V). The force exerted by the gas on the piston (see the figure) is the product of the pressure and the area: F = πr2P. The work done by the gas when the volume expands from volume V1 to volume V2 is W = V2 P dV V1 . In a steam engine the pressure...
Warp drive coolant (density ρ= 1230 kg/m3 runs through a conduit. The square conduit has different...
Warp drive coolant (density ρ= 1230 kg/m3 runs through a conduit. The square conduit has different cross-sectional area A at different points: At point *A, the area is A = 0.810 m2; At point *B, the area is A = 0.540 m2; At point *C, the area is A = 0.697 m2. A 1 m3 portion of fluid flowing through *A has a velocity v*A = 9.333 m/s. At point *A, the (static) pressure pushing the fluid is P*A =...
An ideal gas is held within a cylinder by a frictionless piston that, because of its...
An ideal gas is held within a cylinder by a frictionless piston that, because of its mass, exerts a constant force on the gas in the cylinder.The gas is initially at 2.3 bar absolute pressure and 30oC in the cylinder, and occupies a volume of exactly 20.0 liters. The cylinder is equipped with an internal electric heater to heat the gas. The heater is turned on and produces 150 W of power for three minutes. At the end of this...
1. A hydraulic lift uses a compressor to compress the hydraulic fluid with a moving piston...
1. A hydraulic lift uses a compressor to compress the hydraulic fluid with a moving piston (piston A) of radius RA = 4.83 cm. A second piston (piston B) of radius RB = 18.48 cm is used at the lift to lift cars. What force must be applied by piston A to lift a 14,871N car with piston B? 2. When a 0.438 kg mass is hung from a certain spring it stretches 0.119 m to its equilibrium position at...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume...
3.) What is the most accurate statement concerning the spring constant (k)?          A. The spring...
3.) What is the most accurate statement concerning the spring constant (k)?          A. The spring constant is the ratio of the displacement of the spring from its equilibrium position divided by the force applied to the spring          B. When the displacement of the spring from its equilibrium position is plotted (y-axis) against the force applied to the spring that caused             C. Spring constant is a unitless number related to the “stiffness” or strength of the spring.            ...
1. The maximum weight percentage of carbon atoms (which are very small atoms) that can be...
1. The maximum weight percentage of carbon atoms (which are very small atoms) that can be contained in spaces between the iron atoms in a crystal of face-centered cubic iron at 1333 deg F (723 degC) is 0.8%C. (a) To what approximate atomic percentage does this correspond? (b) On the average, how many unit cells of face-centered cubic iron would have to be examined before encountering a carbon atom? 2. (a) Briefly explain the concept of driving force. (b) What...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT